Large Format Slate Kitchen Floor Tiles Renovated in Blackwood

A client of ours recently moved into a relatively new property in the town of Blackwood where the black slate floor looked dull and the grout was stained. Large format slate tiles were installed though the kitchen and adjacent dining and utility room and they were keen to see if the floor could be brought back to life.

Dull Slate Kitchen Floor Tiles Before Renovation in Blackwood

I went over to survey the floor and could see that the old sealer was failing and letting dirt into the pores of the stone which was especially notable in the busier parts of the floor which had seen the most foot traffic. The solution would be to strip the floor of the old sealer, clean up the grout and reseal. I conducted a number of test cleans to work out the best way to how best to strip off the old seal and get back down to the natural stone. However, as it turns out removing the old sealer was proving to be quite a job and I was concerned that this task alone could potentially take days.

Unhappy with the way things were going I consulted the Tile Doctor help line and we deduced that the sealer applied previously was most likely a heavy duty/industrial product. My client had only just moved into the property and didn’t know the history of the floor so couldn’t help pin point what was used before. The way forward was to strip the old sealer off the floor using abrasive pads.

Now I had an efficient strategy for renovating the floor I was able to provide the customer with an accurate quote which was accepted, and we agreed a date to return and complete the floor.

Cleaning a Dull Slate Tiled Floor

To begin the restoration, I pre-wet the floor with water and using a weighted floor buffer ran a coarse 100-grit milling pad several times across each tile. This process strips the dirt and sealer off the stone slowly turning the water into a grey slurry. Once the whole floor had been treated in this way, I rinsed the slurry off the floor and extracted it using a wet vacuum. The next step was to repeat the process using a 200-grit burnishing pad which being finer closes the pores in the stone and refines the surface further.

The next step was to clean up the grout using Tile Doctor Pro-Clean which is a strong alkaline cleaner. You apply a strong dilution to the grout lines and then scrub it in with a stiff brush. Fortunately, the slate tiles were large format size so there was less grout to deal with than usual. Once that was done the tile and of course grout was rinsed again with more water and then dried again using the wet vacuum.

Dull Slate Kitchen Floor Tiles During Renovation in Blackwood

I have to admit the stripped slate looked pretty awful at this stage in the restoration, but we were now back to the natural stone which was clean and free of all sealers. I left the floor to dry off fully overnight confident in the knowledge that with the application of a fresh sealer it would look a lot different.

Sealing a Slate Tiled Floor

The next day I returned to the property to seal the floor. Before doing so, however, I needed to test the Slate for moisture as you shouldn’t apply a sealer to a damp floor. The results were fine, so I proceeded to apply the sealer which for this installation I used several coats of Tile Doctor Seal and Go.

I chose Seal and Go for this floor as it works well on Slate resulting in a deep durable satin finish that the customer wanted. Additionally, being a water-based product, it doesn’t leave a smell as it dries.

Dull Slate Kitchen Floor Tiles After Renovation in Blackwood

Within two days the floor was transformed, the grout looked much cleaner and the stone looked new. My client was very happy with the work and left the following message on the Tile Doctor feedback system.

Professional, polite and courteous. Paul went beyond the call of duty to help rejuvenate our slate tiled kitchen and utility room floor. He explained each step of the job and provided advice on aftercare and future maintenance. The results are great and I would gladly recommend the services available.
Andy E, Blackwood

 

Renovation of a Dull Slate Tiled Kitchen Floor in Monmouthshire

Source link

Beautiful Black and White Victorian Tiled Hallway Renovation in Monmouth

[ad_1]

This beautiful black & white Victorian tiled hallway was recently discovered hidden under carpet at a house near Monmouth. As well as the years of grime that had become ingrained in the tile, the carpet had been secured with carpet grippers which had been fixed on top of the tiles and the owner was keen to recruit my help in its restoration.

It’s a lovely drive up through the Wye Valley from my base in Caldicot to the town of Monmouth which has a long history that goes back to the Roman times. In fact it’s famous for its “Monnow Bridge” which dates back to medieval times and is the only remaining stone gated bridge of its type left in Britain. Needles to say it has a strong mixture of architecture with many old houses built during Victorian times.

Victorian Floor Before Renovation in Monmouth

Cleaning an Original Victorian Tiled Hallway Floor

The first step in cleaning the floor was to prepare it for cleaning by carefully removing the old carpet grippers and adhesive deposits using a handheld scraper. This was followed by creating a mixture of two powerful cleaning products namely Tile Doctor Remove and Go and NanoTech HBU remover. Remove and Go is a coatings remover designed to strip off old sealers whilst NanoTech HBU is a powerful Heavy Build-Up Remover that uses tiny abrasive particles to clean up tile and stone.

The floor was smothered in the cleaning solution and it was allowed to soak into the tile for about twenty minutes before scrubbing it in. It was not an exceptionally large hallway so a lot of hand scrubbing was required to get the floor as clean as possible. The cleaning solution was rinsed off with water and then extracted using a wet vacuum or wet vac as my colleagues often refer to it.

To finish off the cleaning process I scrubbed a dilution of Tile Doctor Pro-Clean into the grout lines to get them as clean as possible and then gave the floor a final rinse. I need the floor to be dry before sealing so using the wet vac I extracted as much moisture from the floor as possible.

Sealing an Original Victorian Tiled Hallway Floor

I left the floor to dry completely overnight and returned the next day to finish the floor off with a few coats of sealer. On my arrival I started by taking a few reading with a damp meter to ensure the floor was ready to be sealed. Fortunately by efforts with the Wet Vac the night before had paid off and it confirmed the tiles were dry and ready to be sealed.

To do this, I used multiple coats of Tile Doctor Seal and Go which works really well on Victorian Tiles and adds a nice low sheen that brings them up nicely. Naturally the sealer not only improves the way they look it also makes them much easier to clean and will protect them against ingrained dirt and staining.

Victorian Floor After Renovation in Monmouth

I think you will agree this old floor has been transformed and now has a new lease of life.
 
 

Professional Renovation of a Carpet Covered Original Victorian Tiled Hallway in Monmouthshire

[ad_2]

Source link

Specialist Repair of a Damaged Victorian Tiled Hallway in Newport

[ad_1]

Newport is the third largest city in Wales with a long history that goes back to the Roman times so un-surprisingly it has many period buildings and problematic tiled floors. I was recently asked by a Tile Doctor colleague of mine to assist him with the restoration of an original Victorian tiled hallway at a property in the city.

You will see from my website that I have a lot of experience in rebuilding Victorian tiled floors and on this occasion my colleague required me to perform some specialist tile repairs before he could carry out the business of cleaning and sealing the floor.

The property owner had previously asked a different company in to carry out the floor restoration but the tile repairs made were disastrous. The repair attempts were never going to be successful as this was a particularly difficult situation and required real specialism in dealing with Victorian tiles.

Victorian Hallway Tiles Before Repair in Newport

The previous company had used dry plaster to bed the tiles in the hope of being able to achieve some sort of flatness to dry cut the pieces in place. This had also been done without consideration for matching the colours of the tiles. You can see the result of this in the photo below.

Victorian Hallway Tiles During Removal Showing Plaster Base in Newport

Repairing a Victorian Tiled Hallway

The first stage of the repairs was to remove all the plaster powder and cut out the very damaged tiles as far back as possible, being very careful not to cause any further damage to the existing tiles. Next, I cemented the base level to the desired thickness and left it to dry out, before dry cutting all the tiles (150 x 150) I had sourced to colour match with the original tiles.

Victorian Hallway Tiles During Base Rebuild with Cement Newport Victorian Hallway Tiles Cutting Replacements in Newport

Once all the tiles were cut, I moved them to the area to be tiled and proceeded to spread adhesive and install the tiles. Following this, I left the floor to dry out overnight. The next day, I returned to the property and grouted the tiles.

Victorian Hallway Tiles During Replacement in Newport Victorian Hallway Tiles During Replacement in Newport

Now that the repairs have been completed to the required standards, this Victorian tiled hallway is now ready to be cleaned and sealed by my colleague.

Victorian Hallway Tiles Grouting in Replacement Tiles in Newport Victorian Hallway Tiles During Replacement in Newport

 
 

Damaged Victorian Hallway Floor Repair and Restoration in South Wales

[ad_2]

Source link