Renovating Dull Semi Riven Black Slate Flooring in Bentham

This is a Semi Riven Black Slate floor which had been installed throughout much of the downstairs floor at a property in Bentham which is right on the Eastern edge of Lancashire. The Black slate and Grout had seen some wear and was now more Grey than black and having recently installed a new Kitchen the owner wanted the floor to look its best.

Rough stone can be especially hard to maintain if the wrong sealer has been applied. With rough or textured stone, it’s always best to use an Acrylic Sealer (aka ” Topical sealer”) where possible. Unlike a Matt finish impregnating sealer a Topical Sealer is designed to sit on the surface of the Stone preventing dirt from getting caught in the nooks and crevices making it much easier to clean.

Rough Black Slate Floor Before Cleaning Bentham

After surveying the floor, I recommend burnishing the stone with a coarse pad to deep clean the stone and remove any remaining sealer, then seal with Tile Doctor Seal and Go which is a Topical sealer which we find always has provides good results on this type of floors. Happy with the price and keen to get the floor renovated we were given the go ahead and scheduled a date to return to do the work.

Rough Black Slate Floor Before Cleaning Bentham

Deep Cleaning a Semi Riven Black Slate floor in Bentham

The last thing we want to do is cause any damage to their beautiful new wooden kitchen. So before starting the cleaning process I applied clear silicone to the base of the new Kitchen units, this prevents water from the cleaning process seeping into the woodwork through capillary action.

Rough Black Slate Floor Applying Silicone Bentham

To get the tiles clean we burnished the stone floor with a coarse 200-grit Diamond pad fitted to a buffing machine running at slow speed and using water for lubrication. This gives a really deep clean and was followed up with the application of a black scrubbing pad to remove any excess resin released from the Slate which is quite common with Black stones due to the oil content. Once the Slate was clean, we turned our attention to the grout which was scrubbed with Tile Doctor Pro-clean. The floor was then rinsed with water and the soil extracted with a wet vacuum, once done the floor was left dry out.

Whilst at the property we managed to resolve a problem with a poorly laid slate tile in the hallway which the customer had often tripped over, so much so they had covered it with a rug, which was fine, but you couldn’t see the Slate. Rather than lift and relay the tile I managed to cut back the surface of the stone with a hand held flex machine using several different diamond grits. You can see from the pictures how this looks before, during and after the seal. A further advantage of treating the stone in this way is that the slate takes on a more polished finish as the rough texture is cut back. The results speak for themselves and the customer certainly won’t be tripping over the tile from now. With no further need for the rug they can get the full benefit of the slate floor.

Rough Black Slate Tile Before During After Surface Correction Bentham

Sealing a Riven Black Slate Tiled Floor

The floor was left to dry off overnight and we returned the following day to apply a sealer first checking the floor was dry using a moisture meter. All was well, so we started to apply the first of several coats of Tile Doctor Seal and Go. It was a large area across multiple rooms, so it took some time before the job was complete.

Rough Black Slate Floor After Cleaning Bentham

The sealer added a lovely subtle sheen to the floor and restored the black colour in the Slate, the grout was also much cleaner and floor look transformed from the grey dull appearance we first experienced. As usual before leaving we talked about aftercare, using warm water (not hot or cold) with a mop and bucket and half a cap of Tile Doctor concentrated Neutral Tile Cleaner. Using the correct cleaning product will ensure they get maximum life out of the sealer.

Rough Black Slate Floor After Cleaning Bentham

 

Professional Renovation of a Black Riven Slate Tiled Floor in Lancashire

The post Renovating Dull Semi Riven Black Slate Flooring in Bentham appeared first on Tile Doctor Lancashire.

Source link

Dull Riven Black Slate Floor Transfored in High Bentham

[ad_1]

We were asked to come and advise a customer regarding their stone floor which the customer was struggling to keep clean. The property was in High Bentham which lies on the River Wenning, just West of the Yorkshire Dales National Park.

Slate Floor Before Cleaning High Bentham

We often get customers who give up looking after their tiles after a while as some stone like this Black Riven Slate need quite a bit of upkeep to keep them looking good and a standard mop and bucket at times isn’t enough to keep them looking pristine. In this case the sealant had worn away in the high traffic areas and the floor had a slightly rough texture to the surface which meant it was holding onto dirt making it difficult to keep clean. We proposed the floor should be cleaned and resealed, discussed the cost and agreed a time for the work to be carried out.

Slate Floor Before Cleaning High Bentham

Cleaning a Black Riven Slate Tiled Floor

To get the tiles clean we burnished the stone floor with a coarse 200-Grit Diamond pad fitted to a weighted buffing machine using water for lubrication. The floor was then rinsed and then the process repeated using a series of different graded pads, namely the 400 and 800 grit burnishing pads which further cleaned and resurface the appearance of the stone.

The grout was cleaned using Tile Doctor Pro-Clean which was scrubbed into the grout lines by hand; Pro-Clean is a heavy-duty cleaner which gets to the really stubborn stains and it did a great job at getting the grout looking like it should. The cleaning process was then finished off by rinsing the floor with water and extracted the slurry with a wet vacuum. The floor was inspected and retreated to the same process where more work was required. We usually find leaving Pro-Clean on a stain for longer and assisting with a bit of steam helps to lift the dirt out of the pores of the stone.

Once cleaned thoroughly we rinsed the floor again and then extracted as much moisture from the floor as possible with a wet vacuum before leaving it to dry off fully overnight.

Sealing a Riven Black Slate Tiled Floor

We called back the following day to apply a sealer first checking the floor was dry using a moisture meter. All was well, so we started to apply the first of two coats of Tile Doctor Colour Grow, a third coat was attempted but the slate would not accept any more sealer, and this was removed with a cloth. It is important to know if you have reached FCS (Full Cure Sealability) if not then the pores of the tiles will still be open to accepting dirt and the job won’t last long. Over a very short period of time the tiles will diminish in stature and finish.

Slate Floor During Sealing High Bentham

The sealer really restored the black colour to the Slate and transformed the look of the floor. As always, we left the customer a free bottle of Tile Doctor Neutral Cleaner, using the correct cleaning product in future will ensure they get maximum life out of the sealer.

Slate Floor After Sealing High Bentham Slate Floor After Sealing High Bentham

The floor looked lovely when finished and the customer was very happy with the overall result.

 

Professional Renovation of a Black Riven Slate Tiled Floor in Lancashire

[ad_2]

Source link