This Quarry tiled floor was at a house in the town of Market Harborough and as you can see from the photograph below it was in a right state due to the plastering that had gone on previously while the property was refurbished. The plasterer has taken no steps to protect the tiles and as a result there was plaster and plaster dust ingrained into the tile.
Deep Cleaning Quarry Tiles
To clean the floor and remove mess of plaster that it has become covered it the whole floor was soaked in a strong dilution of Tile Doctor Remove and Go which is a strong coatings remover that is safe to use on tile, stone and grout. If was left to dwell on the tiles for around twenty minutes before being worked into the floor with a rotary machine fitted with a black scrubbing pad, the grout was also scrubbed but this needs to be done by hand with a stiff brush. The soiled cleaning solution is then rinsed away using a wet vacuum and the process repeated on stubborn areas until all the tiles were clean. Once I was happy the floor was in an acceptable condition it was thoroughly rinsed with water to remove any cleaning products that might upset the sealer and then left to dry overnight; the wet vacuum was used again to remove the water and help dry the floor.
Sealing Quarry Tiles
We delayed our return until the decorators had painted the walls and unlike the plasterers they protected the floor so we didn’t have to spend time removing paint from the tiles. The tiles were thoroughly dry when we returned and so we got straight on with the task of sealing them with five coats of Tile Doctor Colour Grow which is an impregnating sealer that occupies the pores in a tile preventing contaminates from become ingrained and as its name suggests does a great job of enhancing the colour in the tile.
This is an original Victorian tiled hallway floor in Cardiff that dated back to when the house was built in the year of 1890. The previous householders of which had a radiator installed serviced by laying pipes right through the middle of the floor destroying the tiles as they went, they then back filled the channel with cement. On top of that many of the other tiles had been splashed with cement and paint.
Repairing Victorian Floor Tiles
My first job was to carefully remove the cement from the channel and to precisely cut back any old cement bedding and old cement grout away from any tile edges in preparation for the replacement tiles which fortunately I was able to get hold of.
After all the previous preparation I started carefully scraping off cement from all around the edges of the remaining tiles as well as gloss and emulsion splashes from the surface essentially giving the whole floor a thorough scrape with a hand held scraper vacuuming up the mess as I worked. Interestingly for a floor of its age I tested the floor in various places for moisture and found it to be perfectly dry.
Cleaning a Victorian Floor
To clean the floor I mixed three parts Tile Doctor Remove and Go with NanoTech UltraClean which basically adds small abrasive particles to a powerful sealer and coatings remover making it even more effective. This was applied to the whole floor and left to soak in for an hour making sure not to let it dry out by applying further amounts; leaving it to dwell for an hour gives it time to eat away at any dirt and coatings on the tile making the scrubbing processes easier.
To scrub the tiles I used a rotary machine fitted with a black scrubbing pad rinsing and extracting the soiled solution along the way. This cleaned up the tiles well however there were still some cement stains so this time Tile Doctor Grout Clean-up was applied to the floor in sections and left to ten minutes to dwell before working it in with another black scrubbing pad and rinsing off. This product is acid based so you can’t leave on the tiles for too long; once I was happy with the final result the whole floor was given a thorough rinse with plenty of clean water using a wet vacuum to extract the waste and dry the floor.
The channel was then filled with cement and once it had set replacement replica Victorian tiles from The Original Tile Company were installed. I then grouted the floor in a medium grey grout let the tiles become solid and the grout go hard before using a steam cleaner to make sure that I have removed all the tile doctor cleaning solutions prior to sealing.
Sealing a Victorian Floor Sealing
The customer wanted a semi-gloss finish so once I had tested the floor again to make sure it was dry I sealed the tiles with Tile Doctor Seal and Go which enhanced the colour of the floor tiles and added a nice sheen.
As you can see the new tiles fitted beautifully and the old floor tiles cleaned up so successfully the difference is impossible to spot. It was a lot of painstaking work though taking five days to finish but well worth the result.
Southport is an interesting seaside town with many Victorian terraced properties so it came as no surprise when I was asked to maintain a Victorian Tiled hallway in the town.
Cleaning a Victorian Floor Tiles
The floor was in good condition for its age and just in need of a clean and re-seal to keep it looking good, hallway area’s as you can imagine get more footfall than other parts of the house so are more likely to need a regular deep clean.
To get the floor clean and remove any remaining sealer the floor was sprayed with Tile Doctor Remove and Go which was left to soak into the tile for five minutes before being scrubbed in using a rotary machine fitted with a black scrubbing pad. The next step was to wash off the residue with water which was then removed using a wet vacuum. Following this the tiles were given a rinse in Tile Doctor Grout Clean-up which is an acid based product that can remove grout smears and mineral deposits, it also improves the ability of the sealer to bond with the tile. Last step before sealing was to give the floor a thorough wash down with clean water, which is designed to remove any trace of cleaning products before sealing; the water was removed with the wet vacuum and then left to dry overnight.
Sealing the Victorian Tiled Floor
The next day I returned and checked the floor for dampness using a Damp Meter which indicated the floor was dry and ready for sealing. For Victorian Floor tiles I recommend several coats of Tile Doctor Seal and Go which provides a low sheen finish whilst offering great stain protection.
The customer called me in to resolve a problem in at a beautiful holiday cottage in Cockermouth which had an old Quarry tiled floor installed which she had tried to make shine but had ended up turning it pink in places
Cleaning Quarry Floor Tiles
On my arrival I spent time protecting the kitchen units and adjacent wooden floor and then started on removing the old sealer with Tile doctor Remove and Go; I sprayed it on working in small areas and working it into the tile with a brush making sure to scrub it in well, the resultant soiled solution was washed off with clean water the and then removed using a wet vacuum. After finishing with the tile I moved onto the grout joints using the same process to make sure they were all clean and then the floor was given a good rinse to neutralise the floor before sealing. Again a wet vacuum was used to remove any liquids from the floor and it was then left to dry fully overnight.
Sealing Quarry Floor Tiles
The next day I returned to the cottage and after verifying the floor was dry with a damp tester it was sealed with four coats of Tile Doctor Seal and Go which provides on-going protection as well as adding a nice shine to the tile.
This job took me two days and whilst I was there I took the time to explain how to maintain the floor going forward and the importance of using a Neutral Cleaner to extend the life of the sealer. Certainly the customer was very happy with the results and left the following message our feedback system:
“Absolutely delighted the tiles were very marked in places but Heidi has managed to get them off and the tiles are back to their true colour which I hoped they would be. Heidi explained step by step the procedure and I am very pleased with the result Thank you very much for the time spent and I would recommend Heidi — Veronica”
On a visit to a customer to a customer in Beckenham, Kent who had a pair of rugs that needed cleaning I was asked to take a look at her Encaustic kitchen floor tiles which had become dull and she couldn’t keep them clean. I carried out a demonstration on how I would clean them and also explained the different sealer options available and how each sealer can have a different effect. She was pleased with the demonstration and engaged me to clean the tiles as well as the rugs specifying a sealer that would leave a sheen on the tile.
Cleaning black Porcelain floor tiles
I set about scrubbing the floor using a hot water dilution of Tile Doctor Pro-Clean Tile and Grout cleaner combined 50:50 with NanoTech UltraClean which adds tiny abrasive particles to the solution to make a more effective cleaning product. The solution was worked into the tiles by scrubbing with a rotary machine fitted with a black scrubbing pad and a stiff hand brush was used along the tight grout lines. The soiled solution was removed using a wet vacuum and floor thoroughly rinsed down with clean water. The tiles were then left to dry with the aid of a Turbo Air blower to help speed up the drying time.
Sealing Encaustic Floor Tiles
Once the tiles were dry I applied five coats of Tile Doctor Seal and Go which is a water based protective sealer that doesn’t give off any odour and produces a nice low sheen the customer was looking for.
The final result was one happy customer with a clean easy to maintain tiled floor and two clean rugs as well.