Ruined Marble Shower Tiles Restored in Sharnbrook


I was contacted by the owner of a cleaning company in Milton Keynes, after an end of tenancy clean at a house in Sharnbrook went wrong. Unfortunately a member of their staff had incorrectly applied an acid based cleaning product to the Marble shower tiles which like most natural stone is acid sensitive. The cleaning product had etched the stone causing the damage you can see below. Being a reputable company they were determined to put the situation right and we were asked to step in.

Marble Shower Cubicle Before Cleaning in Sharnbrook

We have had a few issues of this type before where customers keen to remove unsightly Limescale marks from their stone tiles use a household cleaner without reading the bottle label first to see if it’s safe to use. Issues of this nature on Marble cannot be easily resolved with chemical products; it takes specialist knowledge and equipment.

Marble Shower Cubicle Before Cleaning in Sharnbrook

The quote was given and accepted and the work was booked in with the letting company for a few weeks later.

Cleaning and Polishing a Marble Shower Cubicle

The first photos show the extent of the damage which had not only damaged the immediate area but as the cleaning product was in liquid form it had ran down the wall had totally ruined the surface of the tiles in the lower half of the shower.

The first thing I did was to protect the shower tray with towels and then began assembling the equipment needed for this job which consisted of a wet polisher, a variable speed polisher, one set of 6” Tile Doctor burnishing pads from 100 grit to 3,000 grit and one full set of diamond blocks from 80 grit upwards.

I then went about testing how far down the scale I would have to go to get the best results. I found that in most areas the application of a 200 grit burnishing pad was adequate to resurface the tile and remove damage but in some areas I had to go down the scale as low as 80 grit to achieve the desired result.

Marble Shower Cubicle During Cleaning in Sharnbrook

One the damage had been removed the higher grit pads are used in sequence to restore the polish finishing with the 3,000 grit pad. No chemicals are used in this process, just water and the small six inch diamond encrusted burnishing pads which fit to a hand buffer.

Although only a small area, no more than 4 m2 this job took most of the day. However, as the whole shower room was tiled in the same tiles it was a much more cost effective to restore the damaged tiles than replace them.

Marble Shower Cubicle After Cleaning in Sharnbrook

We were able to achieve an excellent result which the client was very happy with, no doubt saving the cleaning company thousands of pounds in replacement costs.

Marble Shower Cubicle After Cleaning in Sharnbrook
 
 

Professional Restoration of a Damaged Marble Tiled Shower Cubicle in Bedfordshire



Source link

Acid-Damaged Marble Shower Cubicle Restored in Leatherhead


Marble tiles are a fantastic choice of stone for a shower cubicle because of its distinctive characteristics and quality. It can really add a luxurious feel and when used in a bathroom take it to the next level.

However, it’s extremely important to note that Marble like all natural stone is a porous and acid-sensitive material. It must therefore be cleaned with care using suitable products. This particular Marble tiled shower cubicle at a property in Leatherhead is a good example of this done wrong. The owner had used an acid-based cleaning product to clean the stone, resulting in damage to the sealer and causing unappealing streaks to form.

Marble Shower Wall Leatherhead Before Cleaning

This type of damage can appear irreparable but, with the right combination of cleaning methods and products, it can be fixed. Once the old sealer has been removed, and the tiles have been cleaned, polished and re-sealed, they can look as a good as new. Here’s how I helped this customer restore the Marble shower cubicle.

Cleaning and Polishing a Marble Shower Cubicle

To begin the restoration, I scrubbed the dirty grout lines using Tile Doctor Pro-Clean, which is a highly reliable and multi-purpose alkaline-based product. I then rinsed the tiles with water to remove the traces of cleaning product.

Next, I moved on to the polishing stage of the restoration – what we often refer to as burnishing. This involved the use of small six-inch diamond-encrusted burnishing pads applied with a hand buffer and with different levels of grit – ranging from Coarse to Very Fine. I started with the Coarse grit pad and worked my way sequentially through our four-pad system, polishing the stone with Medium, Fine and eventually the Very Fine pad to really bring up the polish.

Sealing a Marble Shower Cubicle

Once the shine had returned to the Marble and the damage had been removed, I re-sealed the tiles using two coats of Tile Doctor Colour Grow, a penetrating sealer designed to enhance the natural colours and patina of the stone. Once dry, I gave the tiles a final polish with a white buffing pad to put the finishing touches on the restoration.

Marble Shower Wall Leatherhead After Cleaning

The customer was thrilled with the results, saying:
“I’m really happy with the result and we will make sure we don’t use supermarket cleaners again on natural stone. Rupert was a very personable tradesman who took pride in what he was doing. He has identified Tile Doctor Neutral Tile Cleaner as being the product we should have used in the first place and has sent me the website details.”
Another satisfied customer!
 
 

Professional Restoration of a Damaged Marble Tiled Shower Cubicle in Surrey



Source link