Cleaning Unique London White Limestone Flooring in Leyburn


This floor is London White Limestone which is a very expensive but stunning stone that costs around £60 per square metre. It’s a pale stone that has a wonderful texture and aged appearance that makes it quite unique. Unfortunately, however being a pale stone, it didn’t photograph well, especially in low light so apologies in advance for the poor photographs.

The stone was installed in a very large area across much of the ground floor of this stunning house in the North Yorkshire spa town of Leyburn. The property was in the centre of the town which is just 13 miles from the Yorkshire Dales National Park. There were four areas in total that needed attention, two of which were still quite clean, the main areas that needed attention were the high traffic areas around the entrance hall and kitchen which needed a full clean. The sealant had started to break down and with the stone being white, the floors were looking a bit dirty and drab.

London White Limestone Before Cleaning Leyburn London White Limestone Before Cleaning Leyburn

The two other rooms were only laid around a year ago and were still clean and unmarked however due to the state of the other floors the customer was concerned about the original sealer that had been used and so I agreed to top up the seal in these rooms with a different product to add more protection. Lithofin Stain-Stop had been used previously which from my experience isn’t up to sealing Limestone properly, so l said l could apply a more effective sealer which would penetrate the existing and provide more protection. To make matters worse the client had been using household cleaners which weren’t suitable for cleaning a sealed floor. We agreed a price for the work to be carried out, which the client was happy with, the work was scheduled in for a few weeks later.

Cleaning a London White Limestone Tiled Ground Floor

After adding protection to the skirting boards, I started cleaning the stone in the entrance and kitchen areas. I find you get the best results on Limestone by applying a series of Diamond encrusted honing pads which clean and hone the stone. They are applied in sequence starting with a coarse 400-grit pad followed by the medium 800-grit and then fine 1500-grit pad. The pads are applied with water to provide lubrication and the floor rinsed in between the application of each pad with the soil being extracted with a wet vacuum.

If you have read any of my other posts, you are would probably be expecting me to follow-up the burnishing process with a 3000-grit polishing pad however that wasn’t required in this case as we only use that on polished stone to achieve a deeper shine. The immediate result was a lightly polished floor which looked much brighter than before.

Sealing a London White Limestone tiled Ground Floor

The floor was left overnight to dry off, I double checked with the moisture meter that the previously cleaned area was dry and then all four areas were sealed the next day using a couple of coats of Tile Doctor Ultra-Seal. This is a premium, no-sheen, natural-look, solvent-based penetrating sealer which is created to provide maximum stain protection without changing the appearance of the beautiful stone floor.

London White Limestone After Cleaning Leyburn London White Limestone After Cleaning Leyburn

For after care I recommended to my customer the use of Tile Doctor Stone Soap which will clean the floor without prematurely eroding the sealer. The client was very happy with the finish and thankful for the maintenance advice that will help them maintain their beautiful stone floor in good condition.

 

Professional Clean and Seal of White Limestone Floor in North West Yorkshire



Source link

Dirty White Limestone Tiled Kitchen Floor Cleaned in Wallingford


Photographs below of a White Limestone tiled kitchen floor at a house in Wallingford that was proving difficult for the owner to clean effectively. I went around to inspect the floor and could see that the sealer had worn off leaving the tiles vulnerable to dirt becoming ingrained in the pores of the stone. Once this happens it makes the job of keeping the floor clean quite difficult as you really need to get the dirt out of the pores of the stone to do it right and of course once you do dirt will soon become trapped again without a sealer in place.

Given these Limestone tiles were White the dirt was more visible than usual, so the customer was keen to have the floor deep cleaned to remove the ingrained dirt and then sealed to prevent the problem reoccurring.

White Limestone Floor Wallingford Before Cleaning White Limestone Floor Wallingford Before Cleaning

Cleaning White Limestone Kitchen Floor Tiles

To restore the floor back to its original condition I used a set of burnishing pads which are encrusted with industrial diamonds and come in different grades from coarse to very fine. Applied with a little water the coarse 400 grit pad is designed to strip the floor of dirt and old sealers whilst the remaining pads which are a finer restore the polished surface. Between each pad you need to rinse the floor with fresh water which is removed with a wet vacuum before finally being left to dry overnight.

On this occasion I found when I started with the 400 grit pad it wasn’t having the effect I was expecting and quickly established that this floor would need grinding back with a much coarser milling pad first. Fortunately I have numerous different types of pads available and was able to switch to a 50 grit milling pad which not only got rid of any remaining seal but also grinded out the ground in dirt. This does leave the stone in a rough condition so to restore the final finish I followed up with the 400 and 800 grit pads and finished with the 1500 grit pad, rinsing with water between each pad to remove the soil that is generated. It was quote a large floor, so it took two days to complete the process over every Limestone tile.

Sealing White Limestone Kitchen Floor Tiles

To seal the floor, I used Tile Doctor Ultra Seal which works by impregnates the stone occupying its pores and thus preventing dirt from becoming ingrained in there. This particular sealer doesn’t change the appearance of the stone and so leaves it with a natural look. Again, it was a large area, so it took two days to apply two coats. I then returned on day 5 to go over the whole floor with a 3000 grit polishing pad to give the floor a slight sheen.

White Limestone Floor Wallingford After Cleaning White Limestone Floor Wallingford After Cleaning

 
 

White Limestone Floor Honed and Sealed in Oxfordshire



Source link