Limestone Tiled Floor with Grout Haze Cleaned in Clipston


These photos are of a Limestone tiled floor which was installed in the Kitchen approximately at a property in the small parish of Clipston, which is close to the towns of Market Harborough and Daventry, three years ago. The customer was never very happy with it since it was laid as it never seemed to look clean asked me to cover over and work out what could be done.

On my initial visit I soon realised that the installer had not cleaned off all the grout from the tiles before applying the sealer. This effectively trapped the grout under the sealer and gave the whole floor a dirty appearance, this explained the problem the customer was frustrated with as she could never ever seem to get the floor looking clean.

Limestone Floor With Grout Haze Before Cleaing Clipston

This issue is known as Grout Haze or Grout Smears and is a problem we often come across where the floor has been laid without the excess grout residue being completely polished off the tiles after the grouting. Some manufacturers recommend the tiles are sealed before grouting to make it easier to polish the grout off later. After discussing how we could remedy this I issued a quote which the customer accepted, and we scheduled the work to be done.

Limestone Floor With Grout Haze Before Cleaning Clipston

Removing Grout Haze from Limestone Kitchen Tiles

I arrived on site on the arranged date, as it was a painted kitchen it was not possible to mask up the units, so I used a small hand-held polishing machine fitted with a six inch 400-grit burnishing pad to carefully clean around the edges and break through the sealant. This process was then repeated with a larger seventeen inch 400-grit burnishing pad fitted to a floor polishing machine throughout the rest of the area.

Once the original sealant had been removed using the burnishing pad the next step was to remove the Grout Haze by given the floor an acid wash with Tile Doctor Acid Gel. Being a gel, this product is easier to control than a liquid and sits on the surface where it’s needed to break down the unsightly Grout Haze. It’s left to dwell for a short period before being worked in with a special brush that is designed for this purpose. The resulting slurry is then removed with a professional wet pick up machine and the floor given a rinse with water to remove any trace of the product.

After treating the Grout Haze my next step was to refine the surface of the Limestone using a medium 800-grit and fine 1500-grit diamond encrusted burnishing pad which are applied with water and restore the polished appearance of the stone. The floor is rinsed with more water between the application of each pad to remove the slurry that is generated and then dried with the wet pickup machine.

Sealing a Limestone Tiled Kitchen Floor

I returned the following day to buff the tiles with a white polishing pad as the customer didn’t want a high shine finish which is normally achieved with the 3000-grit diamond burnishing pad, this gave a low sheen honed look as the customer had requested. The floor was then sealed with two coats of Tile Doctor Ultra-Seal which is a natural look sealer that and will protect the newly restored and polished tiles going forward.

Limestone Floor With Grout Haze After Cleaning Clipston

The customer was very happy with the results and has left the following positive feedback on our website.

‘Professional, floor looks much better’ – Vicki S, Clipston

I gave the customer some tips on maintenance and a complimentary bottle of Tile Doctor Stone Soap to enable her to keep the floor looking its best, this product is designed for the regular cleaning of polished stone floors and is pH neutral, so it won’t prematurely degrade the sealer.

Limestone Floor With Grout Haze After Cleaning Clipston

 

Professional Restoration of a Limestone Tiled Kitchen Floor in Northamptonshire



Source link

Marble Bath Surround Polished in Bowden


Although most of the work we do involves floor cleaning you should know we also cover stone worktops in Kitchens and countertops in bathrooms. An example being this opulent bathroom with Marble countertops that surrounded the sink and bath.

The bathroom was installed at a house in the up-market area of Bowden which together with the villages of Hale and Hale Barns are regarded as being the wealthiest parts of Greater Manchester. The customer had got in touch to ask if we could restore the appearance of the Marble surrounds which had become dirty and etched through general use.

Marble Bath Surround Before Polishing Bowden Marble Bath Surround Before Polishing Bowden

Restoring the Appearance of Marble Countertops

My first job was to protect the wood panelling and lush red carpet that surrounds the bath, once all was protected we started to use a set of tile doctor six-inch burnishing pads to clean the Marble and restore the polish.

Marble Bath Surround Before Polishing Bowden

The Burnishing pads come in a set of four and are applied to the stone with a little water in sequence from the coarse 400 grit pad which removes etching and then through the medium 800-grit, fine 1500-grit and finally the very fine 3000-grit pad which restore shine to the Marble. I use a hand-held buffing machine to do this and carefully rinse in-between each pad to remove the small amount of slurry which is generated.

The last 3000-grit pad is applied with just a spay of water using what we call a spray burnish technique, this also has the benefit of leaving the stone dry which is exactly how we need it for the next step in the restoration process which is applying a sealer.

Sealing Marble Countertops

To finish off the restoration, I proceeded to seal the Marble tops with Tile Doctor Ultra Seal which is an impregnating sealer that soaks into the pores of the stone protecting it from within. I should add, Ultra Seal is a natural look sealer that doesn’t change the colour of the stone.

The sealer is applied with a soft cloth, left for five minutes and then the excess is polished off with a soft cloth. We also replaced the silicone sealant around the bath and wash basins and once we were finished the bathroom looked newly installed.

Marble Bath Surround After Polishing Bowden Marble Bath Surround After Polishing Bowden

The customer was over the moon that we brought life back to her impressive bathroom.
 
 

Professional Marble Vestibule Polishing in Cheshire



Source link

Renovating a Water Damaged Riven Chinese Slate Floor in Shipdham


Slow leaking underfloor pipes are guaranteed to wreck the look of an expensive tiled floor and this is exactly what had happened at our client’s house in the village of Shipdham. The problem occurred in the Kitchen and due to the slow nature of the leak it was some time before the problem was diagnosed and repaired. This resulted in a huge damp problem affecting the riven Chinese Slate tiled floor, damaging the sealer and resulting in white efflorescence salts being regularly deposited across the whole area.

The old kitchen units had been removed and the floor partially excavated to access and repair the leaking pipework, after which a new section of slate tiles had been re-laid. The new and the old sections were noticeable, and part of my job would be to clean the old tiles to a standard where they would blend in with the new.

Riven Chinese Slate Floor Before Cleaning Shipdham

Cleaning a Riven Chinese Slate Floor in Shipdham

The first job was to deep-clean the floor using a strong solution of Tile Doctor Pro-Clean mixed with a small quantity of Tile Doctor Remove and Go, which would help to dissolve the damaged sealer. This poured onto the floor and left to soak in for ten minutes before being scrubbed into the slate with our rotary machine fitted with a brush attachment. This brush scrubs right into the uneven surface of the tiles and makes light work of what can be quite a physical job. This process releases a lot dirt and old sealer from the tile which is effectively removed using another machine that gives the floor a power rinse at the same time.

The grout lines and parts of the riven surface which were still soiled were cleaned by hand using angle head brushes and Tile Doctor Oxy-Gel, which is a concentrated version of Pro-Clean in gel form which makes it a lot easier to contain in a small area. Having satisfied ourselves that the floor was finally clean, we left it to dry thoroughly overnight with assistance from our dehumidifier.

Sealing Riven Chinese Slate Tiles in a Shipdham Kitchen

On our return the following day, we damp tested the floor and found that the moisture content was a little higher than we would have liked and this would certainly cause a problem with the standard Tile Doctor acrylic sealer which is water based. In our experience water-based sealers are often only successfully applied if the conditions are ideal and the moisture content of the stone is very low. We chose, therefore, to use a slightly different product in the form of Tile Doctor Seal and Go Extra which is microporous and has a higher acrylic solids content than the standard product, making it ideal in situations where dampness in the tile is an issue but the client wants a sheen finish to make daily maintenance easier.

Six coats of Seal and Go Extra were applied in total, the result had the sheen finish the client wanted and the sealer enhanced the different colours in the slate in the process. The sealer will provide excellent on-going protection and being a fully breathable sealer, it will not be impacted by any damp issues as the floor dries out completely over time.

Riven Chinese Slate Floor After Cleaning Shipdham

With the work completed it the whole floor looked great and it was difficult to spot the repair, our client was certainly happy with the result and made the following comment:

Fantastic service and outstanding results. Our slate floor looks amazing. Very happy
Clair R, Shipdham

 
 

Deep Cleaning and Sealing an Old Slate Tiled Floor in Norfolk



Source link

Ceramic Tiled Bathroom Refresh in St Albans


This was a small family bathroom at a house in St Albans with white ceramic glazed tiles and what was once white grout. The grout was now stained and proving difficult to keep clean, additionally the silicone seal between the tile and the bathtub was perishing. The bathroom needed cleaning and restoring to give it a new lease of life as well as making it easier to maintain for the busy family.

Bathroom Tiles Before Cleaning St Albans

Were actually based in St Albans so always a pleasure to pop round and meet fellow residents. The city dates to the Romans when it was known as Verulamium and these days its popular with commuters working in London.

Cleaning a Ceramic Bathroom Tile and Grout

On arrival I inspected the tiles around the bath and could see they were going to be problematic, the silicone sealant was starting to perish, and I was concerned that the bottom row may be not be watertight. I like to do a job right the first time round so I decided the best thing to do would be to remove the row around the bathroom edge, clean them up and refit them with fresh adhesive, grout and reseal with silicone.

With that in mind my first job was to give the ceramic tile and grout a deep clean by spaying on Tile Doctor Aqua-Pro and then scrubbing it in with polypropylene brushes and pads. This product is designed for the regular cleaning of bathroom tiles as is Tile Doctor Duo-Clean which is a stronger product that can tackle mould as well. The tile and grout were then given a high-pressure steam clean using a special machine we usually use on floor tiles and then let to dry off over lunch.

Ensuring a Tight Bath Seal

After lunch the old silicone was stripped off between the bathtub and wall tile and this was followed by the careful removal of the bottom row of ceramic tiles. This is done by removing the grout first with an oscillating hand tool and then carefully prising the tiles off the wall without damaging them.

Bathroom Tiles Replacement St Albans

The old adhesive was then scrapped off the exposed area to prepare the wall for re-tiling and the tiles were re-installed with fresh. Once the adhesive and gone off the tiles were re-grouted and the grout left to dry before applying a fresh silicone sealant between the tile and bathtub. During the various drying phases, the ceramic bathroom tiles were buffed using a soft white buffing pad to give them an as new appearance.

Bathroom Tiles After Cleaning St Albans

The job was completed in one day and the bathroom now looks like it was recently installed.
 
 

Rejuvenating Ceramic Bathroom Tiles and Grout in Hertfordshire



Source link

Dirty Terracotta Floor Tiles Cleaned and Sealed in Hales


How the Terracotta floor tiles at this property in the Village of Hales, Norfolk became quite so comprehensively dirty in so short a time, we will never know. We were contacted by the new owner, a lady who had become so distressed by the state of the floor in the house she had recently bought that she was seriously considering ripping up the entire area of tiling and replacing it. Remarkable particularly because the property had been restored only a couple of years ago, the kitchen and hallway being laid with new terracotta tiles.

The entire surface was deeply ingrained with soiling and the pointing lines were filthy, despite there being evidence of some kind of topical sealer having been applied at the time of installation. It quickly became obvious during testing that the sealer had been applied very sparingly and had mostly worn away, leaving a badly compromised fluid and soiling resistance with a dull and dirty finish which refused to clean up when mopped.

Terracotta Tiled Kitchen Floor Before Cleaning Hales

Deep Cleaning Terracotta Floor Tile in Hales

The tiles turned out to be made of a fairly soft terracotta which meant that we were able to deep-clean them extremely effectively using a strong dilution of Tile Doctor Pro-Clean (one part Pro-Clean to two parts water). A strong dilution was required to remove what remained of the old sealer in the less used areas and strip the surface back to the bare tile.

The Pro-Clean was left to soak into the floor for about ten minutes before being worked in using our heavy rotary machine fitted with a black scrubbing pad. The resulting slurry being power rinsed and vacuumed away with our 400psi Ninja machine. All the dirt and virtually all of the old sealer was removed at this stage; the remaining patches around the edges of the area being finished by hand with a 200-grit hand-held burnishing block. The pointing lines were then cleaned by hand with neat Pro-Clean and an angled grout brush.

Finally, the deep-seated oil stains in front of the cooker were brought out using Tile Doctor Oxy-Gel which was left to dwell on the marks for an hour before being agitated with a diamond burnishing pad and rinsed away with the Ninja machine. The floor was then left to dry thoroughly overnight with assistance from our dehumidifier.

Sealing Terracotta Floor Tile in Hales

Owing to the softness and consequently high porosity of the substrate, we realised that it could take up to ten coats or more of our chosen sealer in order to achieve the level of shine our client had requested so that the daily mopping would be effective.

Our usual solution to enable us to complete the work in one day would be to apply a coat of penetrating Tile Doctor Colour Grow sealer to the tiles first, followed by up to five coats of topical sealer which would provide the finish, but because our client loved the new lighter colour of the cleaned tiles, Colour Grow was not an option as it is designed to enrich and thereby slightly darken the colour.

The solution therefore was to apply a single coat of Tile Doctor Ultra-Seal which, like Colour Grow, is a solvent-based penetrating sealer but doesn’t alter the colour of the material. This was followed by five coats of Seal & Go to further improve the fluid resistance and provide the mid-sheen finish required.

Terracotta Tiled Kitchen Floor After Cleaning Hales

At the end of the job we had a very happy client whose actual words were: “thank you so much for restoring my faith in my floor!”
 
 

Renovating Terracotta Floor Tiles in Norfolk



Source link

Travertine Kitchen Floor Polished in Stoke on Trent


The pictures below are from a Travertine tiled Kitchen floor I was asked to clean recently at a house in Stoke on Trent. The floor was laid about five years ago and always had a matt appearance and never had a shine at all. I went over to look at the floor and was able to use a spare tile they had to show them how shiny I could get the stone. They were really impressed with the result and could now see the potential of their floor, so they booked me in straight away.

Travertine Kitchen Floor Tiles Before Cleaning Stoke-on-Trent Travertine Kitchen Floor Tiles Before Cleaning Stoke-on-Trent

Cleaning and Polishing Travertine Tiled Floor

Restoring the shine on a polished stone such as Travertine, Limestone or Marble requires the surface to be stripped back and then buffed, which we did by using a set of burnishing pads. These diamond encrusted pads come in different grades from 400 through to 3000 grit and each one does a different job from scrubbing to polishing. I started with the course red 400 grit pad together with a little water to help lubricate and then carried on with the medium Blue 800, then fine Yellow 1500 grit pad, then very fine Green 3000 grit burnishing pads.

My last task for the day was to give the floor a good rinse to remove any remaining soil and then dried the floor as much as possible using a wet vacuum before leaving the floor to dry off overnight.

Sealing Travertine Tile

On our return the next I applied a single coat of Tile Doctor Colour Grow which is a specially designed stone sealer that brings out the deep colour of the stone. Once this had dried I worked in Tile Doctor Shine powder with a buffing pad to give a really deep and durable finish.

Before leaving I finished the floor off by spray burnishing the floor with an ultra high speed burnishing machine fitted with a white buffing pad.

Travertine Kitchen Floor Tiles After Cleaning Stoke-on-Trent Travertine Kitchen Floor Tiles After Cleaning Stoke-on-Trent

For the first time in five years the Travertine floor has a deep shine and my customer was really pleased with the outcome.
 
 

Putting a Deep Shine on Travertine Tiled Floor in Gloucestershire



Source link

Very Dirty Limestone Tiled Kitchen Floor Cleaned in Radcot


I was asked to clean the Limestone tiled floor of a very old house in the Village of Radcot which is close to the River Thames and dates to the 14th Century. Being close to a river is very scenic but can be problematic and I was told the house had experienced flooding in recent years.

Whilst the Limestone floor clearly wasn’t as old as the house it was definitely in need of some attention to remove the dirty that had become ingrained into the pores of the stone and restore its appearance.

Limestone Tiled Floor Before Cleaning Radcot

Cleaning Limestone Floor Tiles

My first step was to let the floor soak for ten minutes in a strong dilution of Tile Doctor Pro-Clean, which is a strong Tile and Grout cleaner. The product was then scrubbed into the floor using a deck brush to remove any surface dirt. I also took the opportunity to clean up the grout before rinsing off the now soiled cleaning solution with water and extracting it with a wet vacuum.

Next I turned my attention to the stone tiles which would need to be stripped back, re-honed and then sealed to protect them. I find the best way to achieve this on stone is through the application of a set of Diamond encrusted burnishing pads.

I started the burnishing process by fitting a coarse 400 grit no.1 burnishing pad to a floor buffer and running at a slow speed, applied the pad over the whole floor. This coarse pad is designed to strip off old coatings and dirt from the tile. You use a little water to help lubricate and once complete it’s necessary to rinse the area with water to remove the soil that is generated. The next step is to start building back the polished surface with the 800 and then 1500 grit pads which are applied in the same manner.

This floor was left to dry before moving onto the final stage of the polishing process which is to apply the very fine 3000 grit which further restores the appearance of the Limestone tile. This last pad is applied dry with a small amount of water sprayed onto the surface to help bring up the shine.

Sealing Limestone Floor Tiles

With the floor dry I moved onto sealing the tiles in-order to protect them from dirt and staining. I used a couple of coats of Tile Doctor Colour Grow for this purpose as this particular sealer enhances the natural colours in the stone. It’s also an impregnating sealer that works by occupying the pores in the stone thus preventing dirt from becoming ingrained in the stone.

My pictures of the floor are not brilliant but hopefully you can see how much more colourful the floor now looks.

Limestone Tiled Floor After Cleaning Radcot
 
 

Limestone Floor Cleaned, Polished and Sealed in Radcot



Source link

Large Limestone Tiled Floor Stripped and Resealed in Weybridge


Weybridge is an affluent commuter town with good train connections into London Waterloo, as a result, there are some impressive houses here, many of which feature beautiful polished stone floors. This particular residence in Weybridge had a very large Limestone tiled floor installed in their Kitchen/Dinning Room, the floor had been cleaned and sealed about a year prior, so it was still in good condition however the customers ageing dog had a few accidents which had damaged the sealer.

Limestone Tiled Floor Before Cleaning in Weybridge

Urine contains Uric Acid which being an acid can damage the sealer, this is why for daily cleaning we always recommend using pH neutral cleaning product such as Tile Doctor Neutral Tile Cleaner or Stone Soap if the floor is polished. Limestone and Travertine are especially vulnerable to acids due to their high levels of calcium carbonate and often results in pock marks or small holes forming in the stone.

Resealing a Polished Limestone Floor

Once we’d moved the furniture to another room I started with a deep grout clean. I ran a dilution of Tile Doctor Pro-Clean along the grout lines then left it to dwell for five minutes while I got the wet vacuum from the van. When ready I cleaned the grout by hand with a hard nylon brush and then extracted the soiled cleaning solution with the wet vacuum.

With the grout now clean and the soil removed I set up my rotary floor cleaning machine ready to burnish the stone tile and restore the finish with a set of diamond encrusted burnishing pads.

The first pad in the set to be applied is a coarse 400 grit pad that is designed to remove existing sealers and dirt and is run over the tiles with water for lubrication. During the following hours the process was repeated with the medium 800 grit and fine 1500 grit pads which gradually polish the stone and return the shine. The floor is rinsed between each pad to remove the soil which is generated from burnishing.

This process took up much of the day so after rinsing the floor after the 1500 grit pad and extracting the soil with the wet vacuum I left the customer strict instructions not to spill anything on the unsealed floor. The tiles need to be dry before re-applying the sealer and any remaining moisture from the rinsing should evaporate overnight.

Sealing Limestone Tiles

Returning the next day, I tested the floor was dry the applied the first coat of Tile Doctor Ultra-Seal which is a natural look impregnating sealer that soaks into the pores of the stone protecting it from within. Once I’d wiped away any excess I left it to dry for half an hour before applying a second coat.

Breaking for lunch allowed sufficient time for the sealer to dry and I was able to complete the floor with a final polish.

Limestone Tiled Floor After Cleaning in Weybridge
 
 

Stripping and Resealing a Polished Limestone Floor in West Surrey



Source link

Dull Encaustic Tiled Hallway Floor Renovated in Berkhamsted


I had an enquiry from a client in the London commuter town of Berkhamsted who had a beautiful Encaustic tiled floor in their hallway which was in need of cleaning. Encaustic tiles are made from layers of cement that are hydraulically compressed to make a very hardwearing surface that can then be decorated. The result is an easy to clean hardwearing surface that is ideal for high traffic areas such as hallways.

Encaustic Tiled Hallway Before Cleaning Berkhamstead

Encaustic tiles however are micro-porous so do need to be sealed to prevent dirt from becoming ingrained in the tiny holes. The tiles at this property in Berkhamsted had been sealed at some point in the past but over the years the sealer had worn down lettering dirt enter the pores making it difficult to clean effectively. The floor now required a deep clean and seal to bring back the life into this artistic floor pattern.

Encaustic Tiled Floor Cleaning

We first removed what was left of the old sealer and ground in dirt using a coarse 400 grit Red burnishing pad attached to a rotary floor buffer. The burnishing pads we use are encrusted with industrial diamond and are applied using water for lubrication, once the pad has been run over all the tiles the floor is rinsed with more water which is then extracted with a wet vacuum to remove the slurry that is generated.

The coarse pad was the followed by a medium 800 grit burnishing pad which is the first step in restoring the appearance of the tiles and is applied and rinsed off using the same process as the 400 grit. The 800 grit pads is followed by the 1500 grit pad which is the second step In restoring the appearance of the tile. Again, the pad is applied with water to lubricate and the floor given a good rinse afterwards.

The next step was to get the grout clean which was done by applying Tile Doctor Pro-Clean which was left for ten minutes before being scrubbed in by hand with a narrow stiff brush. The floor was then given yet another rinse and then dried with the wet vacuum to remove the dirt that was generated from the grout.

The last step in the cleaning process was to run over the floor with a very fine 3000 grit pad, this last pad is the final step in restoring the appearance of the tile and is applied dry with only a little water that is sprayed on using a technique we like to call spray burnishing.

Encaustic Tiled Floor Sealing

Once the floor was dry it was sealed using two coats of Tile Doctor Colour Grow which is an impregnating sealer that seeps into the pores of the tile protecting it from within. This sealer has the added advantage of enhancing the existing colours in the tile improving its overall appearance. The overall process worked incredibly well and made a huge difference to the floor as you can see in the final photograph.

Encaustic Tiled Hallway After Cleaning Berkhamstead

To keep Encaustic floor tiles in first class condition I recommend the use of the Tile Doctor Neutral Tile cleaner which being pH neutral does not reduce the life of the sealer and is ideal for the cleaning of all types of sealed floors. The product comes in a concentrated form, so I recommend it’s used in a mild 1-30 dilution spray applied and wiped over with a microfibre flat mop, then buffed dry.
 
 

Encaustic Tiled Hallway Floor Renovation in Hertfordshire



Source link

Renovating Reclaimed Slate Floor Tiles in Wreningham


When the old Rowntree Mackintosh sweet factory at Chapelfield in Norwich was closed down and eventually demolished, our client acquired a quantity of the beautiful green/black slate flooring tiles which had formed part of the reception area of the plant. They had laid these tiles edge to edge with no grouting in their large kitchen/dining room extension at their home in the village of Wreningham and the result was perhaps one of the most impressive examples of high-quality slate flooring we have ever seen in any location.

The Slate floor tiles had been protected against oil and fluid spillages with the application of a penetrating sealer after installation at the property but, over the ensuing years, there had been some inevitable degradation of the sealer and the entire area was now in need of a thorough deep-clean and reseal in order to remove the coating of general grime, bring out the strikingly deep colour and restore the stain resistance.

Cleaning a Slate tiled floor

As there was no topical finish to remove, we proceeded to deep-clean the surface of the tiles using Tile Doctor Pro Clean at a less powerful mix ratio of 1-part water to 5-parts cleaner. This solution was applied to the tiles and left to soak in for ten minutes before being worked in using a black scrubbing pad fitted to our rotary machine.

The resulting muddy slurry was then power rinsed off the floor with water and then extracted with our Ninja machine which has a very powerful vacuum. The high pH product was so effective, no further cleaning was necessary.

The whole area was then dried thoroughly using two large industrial fans which dramatically reduced the drying time, enabling us to move onto sealing later that afternoon. We don’t normally recommend cleaning and sealing in the same day as the floor has to be dry before sealing however in this case we were able to progress through the cleaning process much quicker than anticipated.

Slate Tiled Floor in Wreningham During Sealing

Sealing a Slate Tiled Floor

Before sealing the floor was spot tested in different places using a moisture meter. All was well, so a single coat of Tile Doctor Colour Grow was applied to the Slate tiles. Colour Grow is a penetrating sealer that seeps into the pores of the stone protecting it from with and as its name suggests also intensified the natural black/green colours of the slate in the process.

Once the first coat was dried I followed up with three coats of Tile Doctor Seal & Go, which further enriched the colour and provided a pleasing mid-sheen finish to the floor surface.

Slate Tiled Floor in Wreningham During Sealing

The whole process really put the life back in the stone floor and the tiles which were once dull now look vibrant and colourful.
 
 

Deep Cleaning and Sealing an Old Slate Tiled Floor in Norfolk



Source link

Mexican Terracotta Kitchen Rejuvenated in Redditch


A customer in Redditch had recently had a new kitchen fitted and prior to that had tried to seal the Mexican Terracotta tiled floor themselves, however they were not happy with the results, so they contacted Tile Doctor to see if an improvement could be achieved. The sealer they used was matt which didn’t show off the Terracotta at its best and the tile and especially the grout were not as clean as they could have been. Getting the tile and grout clean before sealing is essential otherwise you end up sealing in the dirt.

Mexican Terracotta Tiles Before Resealing Redditch Mexican Terracotta Tiles Before Resealing Redditch

To get the best from the floor I recommended stripping off the sealer, giving the tile and grout a deep clean and then resealing with a satin sealer. The customer agreed and keen to get his new kitchen looking its best booked me in to do the work.

Mexican Terracotta Tiles Before Resealing Redditch

Cleaning Original Victorian and Mexican Terracotta Tiles

My first tasks was to protect the new kitchen units from splashing with plastic sheeting and by removing the kick boards. Once done I began the process of removing the existing sealer by applying Tile Doctor Remove and Go which as the name implies is a strong coatings remover that safe to use on Tile and Stone. The product was dilated with water, applied to the tile and grout and left to soak in for about ten minutes. The floor area between the kitchen units was quite tight so on this occasion I decided to scrub the tiles with a deck brush and hand brush as opposed to using a rotary machine fitted with a scrubbing pad. The Remove and Go did the job and the sealer was removed and the floor rinsed off with water to reveal the original tiles.

Mexican Terracotta Tiles During Stripping Redditch Mexican Terracotta Tiles During Stripping Redditch

The next step was to give the Terracotta tile and grout a deep clean by scrubbing in a medium dilution of Tile Doctor Pro-Clean. Mexican Terracotta can be difficult to clean due to the makeup of the tile, but the Pro-Clean scrubbed in with the brushes I used earlier worked well. The now soiled cleaning solution was rinsed off with water and then extracted using a wet vacuum.

The customer had laid some new tiles to fit in with the new units but asked me to grout them so with time to spare before leaving for the day I grouted them in with a flexible grout and polished off any grout smears. It’s important that tiles are dry before sealing so the floor was then left for two days so it could dry out.

Sealing a Mexican Terracotta Floor

Upon my returned to seal the tiles I first checked with a damp meter that they had indeed dried. All was well, so I began the process of applying Seal and Go which is a water-based sealer from the Tile Doctor range that leaves the satin finish the customer wanted, also being water based it doesn’t leave a smell as it dries. Mexican Terracotta is notoriously very porous, so numerous coats of seal are required and in fact this floor needed eleven coats. I applied a few more coats to the new tiles so they would blend in better with the existing tiles.

Mexican Terracotta Tiles After Resealing Redditch Mexican Terracotta Tiles After Resealing Redditch

The customer was very pleased with the results and I left them with a bottle of Neutral Tile Cleaner to help maintain the tiles appearance going forward.
 
 

Stripping, Cleaning and Sealing Mexican Terracotta Floor in Redditch



Source link

Soiled Yellow and Black Victorian Quarry Tile Restoration


These Yellow and Black Quarry tiles are though to be original feature of this Victorian house in Reading and the owner was keen to get them renovated. The tiles were in basement of the house and over the years the tiles had suffered from water damage due to various small floods, they were now heavily soiled and the most challenging task would be to remove a large build up of mortar and cement.

Yellow and Black Quarry Tiles Before Cleaning Reading Yellow and Black Quarry Tiles Before Cleaning Reading

I ran a test clean in a corner of the smallest room to demonstrate the cleaning process and although confident I could significantly improve the appearance of the Quarry tiles. I had to explain to my customer that due to the years of neglect the outcome would not be perfect, however the test clean went well and the customer was happy with the outcome so booked me in to do the work.

Yellow and Black Quarry Tiles Before Cleaning Reading

Soiled Quarry Tile Cleaning

The first issue to tackle was to remove the dirt and ingrain soil which I did by scrubbing in a strong mix of Tile Doctor Pro-Clean which is a strong tile and grout cleaner. The solution was left to soak in before ten minutes before being agitated with a black scrubbing pad fitted to a rotary machine. I then rinsed off the now soiled cleaning solution off using a hot water truck mounted extraction system.

Yellow and Black Quarry Tiles During Cleaning Reading

Now the ingrained dirt was taken care of, the most difficult task was to remove the cement/mortar built up that was covering a high percentage of the tiles. I did this using a combination of Tile Doctor products including Grout Clean-Up, Acid Gel and 50,100 grit diamond pads. I started with Grout Clean-up but found that Acid Gel worked better on this occasion. To deal with stubborn areas I left the Acid Gel to dwell overnight covered with plastic sheeting so it wouldn’t dry out.

The Acid Gel worked wonders and I was able to complete the cleaning process when I came back the next day giving the floor another rinse with the hot water extraction system. With the quarry tiles now clear I able to do a final spot check and used hand held burnishing blocks and very coarse 50 grit milling pad followed by a 100 grit diamond pad and another rinse to finish it off.

Quarry Tile Sealing

After leaving the floor to dry out over the weekend it was ready to be sealed. We had agreed on giving the Quarry Tiles a matt finish so I used three coats of Tile Doctor Colour Grow which is a fully breathable colour enhancing sealer that works well on old clay tiles.

Yellow and Black Quarry Tiles After Cleaning Reading Yellow and Black Quarry Tiles After Cleaning Reading

I’m happy to say the floor turned out very well considering its condition, certainly my customer was very happy with the outcome and left the following feed back on the Tile Doctor Feedback system.

“Fantastic job – completely revived our Victorian cellar tiles, the before and after photos accurately show the difference the work has made! Also impressed by Dennis’s communication and responsiveness to our needs with the work”.

Yellow and Black Quarry Tiles After Cleaning Reading
 
 

Professional Restoration of old Victorian Quarry Tiles in Berkshire



Source link

Screed Covered Quarry Tiled Floor Renovated in Coulsdon


Pictures below of a Quarry Tiled floor that a customer had discovered when taking up the lino at her house in Coulsdon. Realising the floor was original and worth saving she contacted Tile Doctor and I popped round to take a look.

A lot of the tiles had been covered in a screed to provide a flat base for the Lino and that would need removing. In order to be sure what treatments would work to remove the screen and successfully restore the Quarry tiles without causing any damage I ran a couple of tests and everything seemed ok.

Quarry Tiled Floor Before Renovation Coulsdon Quarry Tiled Floor Before Renovation Coulsdon

We could both see the job wasn’t going to be easy and would take some days to complete so I worked out a price which was accepted and we agreed a date for the work to start.

Quarry Tiled Floor Before Renovation Coulsdon Quarry Tiled Floor Before Renovation Coulsdon

Removing Screed from Quarry Tiles

The Quarry tiles in the WC hadn’t been covered in Lino so they would just need a good clean and seal so the main work would be in the Hallway and Kitchen. Fortunately my customer was having a lot of other work done in the house and was in the middle of stripping the walls so I didn’t need to worry too much about protecting the skirting boards etc.

Working in sections I soaked the screed in water and then carefully chipped away at it until it came loose, it was slow work but I could see the process was working as expected and eventually all the Quarry tiles were revealed. There was still a lot of cement from the screed stuck to the surface of the tile so after sweeping up the chippings I set to work applying a strong solution of Tile Doctor Grout Clean-up to the tiles and leaving it to soak in for a short while. Grout Clean-Up is an acidic product that we normally use for removing grout smears from the surface of tiles. The solution was scrubbed in and then rinsed off with water and extracted with a wet vacuum.

Quarry Tiled Floor During Renovation Coulsdon Quarry Tiled Floor During Renovation Coulsdon

To get the tiles in the toilet clean I gave them a good scrub with Tile Doctor Pro-Clean which is a reliable and effective Tile and Grout cleaner. Once clean they were rinsed with water and dried with the wet vacuum.

Sealing Quarry Tiles

I had timed my visit between working being carried out at the property so I was able to leave the floor for a few days so it could thoroughly dry out. I returned later to check the Quarry tiles were dry and completed the renovation by sealing the floor with Tile Doctor Seal and Go which is a water based sealer that works really well on Quarry tiles. Five coats of Seal and Go were needed to fully seal the tiles and the floor now looks transformed.

The owner was very satisfied with the improvements and before leaving I advised to cover the floor before starting the decorating work.
 
 

Old Quarry Tiles Restored in Coulsdon, Surrey




Source link

Deep Cleaning Bathroom Tile & Grout in Beckenham


Recently I was asked to renovate the tile and grout of this windowless bathroom in a Beckenham flat which was not looking its best. The Ceramic tiles had become dull due to a build up of Limescale and the grout had become stained from shampoo dyes and mould.

Ceramic Bathroom Tiles Grout Before Cleaning Beckenham

Without strong ventilation and regular cleaning most bathrooms can end up with these problems however with the right products and techniques they can be renovated as you will see below.

Ceramic Bathroom Tiles Grout Before Cleaning Beckenham

Deep Cleaning Bathroom Tile and Grout

My first action was to apply a liberal amount of Tile Dr Oxy-Gel which is a strong alkaline tile and grout cleaning product that comes in a gel form. Being a gel it’s able to sticks to vertical surfaces for longer allowing it to break down the Limescale and soap residue that had taken up residence. Once it had been left to dwell for around thirty minutes, it was scrubbed off with water and a pan scrapper and then dried with a micro cloth. You can use this process with glazed ceramic tiles like these but for natural stone I would have used a different approach.

I then sprayed Tile Doctor Duo Clean, which is a grout cleaner and mould remover, onto the grout lines. I left the grout with the Duo Clean on it for about ten minutes before scrubbing and rinsing off with water.

The process was repeated where needed until I was happy that the tile and grout were as clean as possible however to really give the bathroom a fresh look I decided to completely renovate the grout with the application of a Grout Colourant.

Grout Colouring Bathroom Wall Tiles

There are ten colours to choose from in the Tile Doctor range of Grout Colourant’s and in this case I felt the best outcome would be to use a White colourant to match the tiles and restore the original look of the bathroom; the customer however wanted a grout colour that would provide a contrast against the white tiles, so in the end we opted for a light grey colour.

The colourant is easily applied directly to the grout and in this case I waited for the tiles to dry before applying two coats with the aid of a small brush making sure to remove any excess that comes into contact with the tile.

I finished the renovation by cutting out the original mastic sealant from around the bath and replacing with a new mould resistant silicone in white to match the bathtub.

Ceramic Bathroom Tiles Grout After Cleaning Beckenham

The bathroom now looks transformed and the epoxy grout colourant adds a layer of protection to the grout that will keep it looking good for some time to come.
 
 

Bathroom Tile Renovation in Kent



Source link

Mouldy Ceramic Tiled Bathroom Restored in Eccles

An elderly couple from the Greater Manchester town of Eccles were in touch recently regarding their Ceramic Tiled Bathroom, they had a big problem with mould build-up due to a broken extractor fan and wanted it removing. Mould grows in humid conditions and with the extractor fan out of action it soon started to spread. If you have been reading my blog, you will have seen some of the bathroom transformations we have completed over the years, so I was confident we could resolve the problem for them and paid them a visit to take a look.

Mouldy Bathroom Before Restoration in Eccles

You can see from the photographs that the tiles were in good physical condition, but the grout and silicone mastic sealant was stained with shampoo dyes and mould spots, the worst part however was the ceiling which was covered in mould growth. I ran a test clean on the bathroom wall grout and ceiling which went very well so we quickly agreed on a date to clean the whole bathroom.

Mouldy Bathroom Before Restoration in Eccles

Cleaning a Ceramic Shower Cubicle

They say you should always start at the top and work down so my first task was to treat the mouldy bathroom ceiling with Tile Doctor Duo Clean which although marketed for use on grout it worked just as well on paint to remove the mould. When done with ceiling I moved on to the wall tiles spraying on Duo Clean, letting it soak in for ten minutes, working it in to the grout with a stiff brush and then rinsing off with water.

With four walls of tile and grout and a ceiling to clean the overall cleaning process took two days to complete and at the end of the second day I turned my attention to the silicone sealant. Taking care not to scratch the bathtub I carefully stripped out the silicone in-between the tile and bath with a sharp knife. Duo Clean works on silicone as well but you do need to catch it early so often the easiest thing to do is to replace it rather than clean it. I replaced the silicone with a good quality mould and bacteria resistant silicone.

When I returned on the next day I carried on with the Top/Down approach by turning my attention back to the ceiling which I painted with a white moisture resistant emulsion paint.

Mouldy Bathroom After Restoration in Eccles Mouldy Bathroom After Restoration in Eccles

With the ceiling freshly painted I then took another look at the grout which although clean was not a perfect white anymore and looked dull and uninviting. We do find this can happen with grout, especially if it isn’t the subject of a regular cleaning regime. There is a remedy though and what we find works well in these cases is to recolour the grout with an epoxy-based Grout Colourant which not only rejuvenates the grout it also protects it for years to come.

Grout Colouring Bathroom Wall Tiles

There are ten colours to choose from in the Tile Doctor range of Grout Colourant however in this case I felt the best outcome would be to use a White colourant to match the tiles and restore the original look of the bathroom.

The colourant is easily applied directly to the grout and in this case, I applied two coats with the aid of a small brush making sure to remove any excess that comes into contact with the tile. After applying the colourant, the bathroom transformation was complete, and it looked like a new installation.

Mouldy Bathroom After Restoration in Eccles

It was a lot of work however I was really happy with the outcome and so were the clients who even left me a nice tip. The last thing to sort out is the extractor fan, however they will need a different tradesman for that job.

Bathroom Tile Renovation in Greater Manchester
Source link http://greater-manchester.tiledoctor.biz/mouldy-ceramic-tiled-bathroom-restored-in-eccles/

Restoring a Carpet Covered Sandstone Hallway in Carbrooke


This was perhaps the most challenging restoration we have been presented with to date.
The work involved removing carpet and underlay from a long Yorkstone tiled hallway at a beautiful old Grange in Carbrooke on the outskirts of Watton and restoring the flagstones to their original glory. These pavers are a type of Sandstone, a carboniferous sedimentary rock consisting of quartz, mica, feldspar, clay and iron oxides quarried in Yorkshire and having a rich sandy colour with a slightly sparkling surface.

On lifting the carpet, we found, to our dismay, that the rubber-backed underlay had been firmly stuck down to the surface of the stone with what appeared to be a thick layer of yellowing impact adhesive which covered the entire area right up to the thresholds and skirting boards.

Yorkstone Hallway Restoration Carbrooke Carpet Removed Revealing Underlay Yorkstone Hallway Restoration Carbrooke Underlay Peeled Back Revealing Glue

Stripping Carpet Adhesive off a Sandstone tiled floor

Our first task was to remove as much of the underlay by hand using sharp-bladed scrapers and a heck of a lot of elbow grease. Having done this, the next step was to cover the remaining adhesive layer with a specialist water-based stripper which was applied by brush and allowed to react for an hour. The result was an incredibly sticky substance with the consistency of chewing gum which we had to painstakingly remove inch by inch with paint scrapers. This process had to be repeated twice as even the specialist stripper couldn’t cope with the sheer volume of goo in a single application. The floor was then left overnight to dry out and settle down.

Yorkstone Hallway Restoration Carbrooke Applying Stripper Yorkstone Hallway Restoration Carbrooke Scraping Away Softened Glue

The following day, we deep-cleaned the whole area using very strong mix of Tile Doctor Pro Clean and Remove & Go, scrubbed in with a rotary machine fitted with a black stripping pad. Four pads were used up in this process as they quickly became clogged with the thick slurry which was then power rinsed and vacuumed away from the floor. Any remaining patches of the glue were further softened using Tile Doctor Nanotech HBU Remover and carefully picked off by hand with the bladed scrapers.

Yorkstone Hallway Restoration Carbrooke Deep Cleaning Yorkstone Hallway Restoration Carbrooke Stone Surface After Deep Cleaning

Finally, the slabs were finished using a brush fitted to the rotary machine with 320 grit honing powder to achieve a smooth, silky and very clean surface before being power rinsed with plenty of clean water. Again, the floor was left to dry thoroughly overnight with the assistance of our large capacity dehumidifier and thermostatic hot air blower.

Sealing a Sandstone tiled floor

Returning the following day, we found that the dehumidifier and heater had done their job and the sandstone was ready for sealing, the moisture content having been brought down to an average of 10% overall as shown by our damp meter testing.

The client had requested a light shine on the floor so that it would be easy to maintain on a daily basis. We chose, therefore, to use Tile Doctor Seal & Go, a combination sealer with a mid-sheen topical finish, which we applied using paint pads and microfibre cloths in five thin coats, resulting in an excellent fluid resistant seal with a lustrous shine.

Yorkstone Hallway Restoration Carbrooke Applying Sealer To Edges Yorkstone Hallway Restoration Carbrooke Finished Floor

This was a tough job but a highly satisfying result, further emphasised when the client’s antique furnishings were placed in situ.
 
 

Deep Cleaning and Restoration of a Sandstone Hallway in Norfolk



Source link

Polishing Limestone Kitchen Floor Tiles in Helsby


Getting the best out of a natural stone floor isn’t straight forward and we often get calls from customers who have come to the realisation they need help. An example of this being a lady from the village of Helsby who got in touch after her husband had given up following spending two days cleaning their Limestone tiled kitchen floor but actually making it worse.

Limestone Kitchen Floor Tiled Before Cleaning

Burnishing and Cleaning a Limestone Tiled Floor

On arrival the first step was to give the floor a general clean with a focus on cleaning the grout lines and removing any grit from the floor. I used a dilution of Tile Doctor Pro-Clean which is an alkaline tile cleaning product that is safe to use on grout and stone. The cleaning solution was applied by sponge mop and left to soak for ten to twenty minutes before being scrubbed in along the grout line using a stiff narrow brush to get them really clean. Once done the floor was then rinsed with clean water and the now soiled cleaning solution removed with a wet vacuum.

Limestone Kitchen Floor Tiled During Cleaning

The next step was to use a set of Tile Doctor burnishing pads to polish the stone back to a deep shine. The pads which are encrusted with industrial diamonds are applied with a rotary floor buffer in sequence from coarse to extra fine. The first pad has a Coarse 400 grit which is applied with only water for lubrication, removes minor scratches, sealers, and the top surface dirt. Working in small areas, I applied the pad across the Limestone, rinsing in between and picking up the soiled solution with a wet-vac machine. I then repeated this same procedure with the Medium 800 grit pad which is the first stage polishing pad again rinsing with water after use. The next two pads are a Fine 1500 grit and Extra Fine 3,000 grit which really build up a high-quality polish on the stone.

Sealing a Limestone Tiled Floor

The floor was left to dry off fully overnight and I returned the next day to seal the Limestone first checking with a damp meter that the stone was dry. The customer wanted a natural look finish to the Limestone, so to seal the tiles I applied two coasts of Tile Doctor Ultra Seal which is an impregnating sealer doesn’t change the look of the stone in anyway. Ultra Seal is an impregnating sealer that works under the surface by occupying the pores in the stone thus preventing dirt from becoming ingrained.

Limestone Kitchen Floor Tiled After Cleaning Limestone Kitchen Floor Tiled After Cleaning

Once the sealer had dried the floor was treated to a gentle buff with a white pad to bring up the shine even further. Once complete the stone looked a lot healthier and the grout looked much cleaner.
 
 

Professional Limestone Floor Polishing in Cheshire



Source link

Polishing Marble Floor Tiles in Willington


Although expensive Marble is a highly coveted, popular and classic flooring choice, not only is it hard wearing you can attain a high polish that simply looks fantastic. At peak condition, it’s one of the most beautiful and eye-catching types of stone available, however it’s appearance will degrade over time and with use, so it does need maintaining.

This customer, who lives in the small village of Willington in Cheshire had contacted us because they were concerned that the lustre on their Marble tiled floor which had been installed throughout much of the ground floor had faded and lost its attractive appearance. We arranged a date to go over and re-polish the floor back to health.

Marble Tiled Floor Before Cleaned and Polished Willington Cheshire

Burnishing and Cleaning a Marble Tiled Floor

On arrival the first step was to give the floor a general clean using a mild dilution of Tile Doctor Pro-Clean which is an alkaline tile cleaning product that is safe to use on Marble. I mention this because there are many cleaning products on the market today which are acidic and really only meant for use on Vinyl and Ceramic tiles. The cleaning solution was applied by sponge mop and left to soak for ten to twenty minutes with a particular focus on the grout lines. I used a stiff brush along the grout lines to get them really clean and then once done the floor was then rinsed with clean water and the now soiled cleaning solution removed with a wet vacuum. This process also has the added advantage of removing any grit from the floor which might cause scratching during the next stage which was to polish the floor.

The next step was to use a set of Tile Doctor burnishing pads to polish the stone back to a deep shine. The pads which are encrusted with industrial diamonds are applied with a rotary floor buffer in sequence from coarse to extra fine. The first pad has a Coarse 400 grit which is applied with only water for lubrication, removes minor scratches, sealers, and the top surface dirt. Working in small areas, I applied the pad across the Marble, rinsing in between and picking up the soiled solution with a wet-vac machine. I then repeated this same procedure with the Medium 800 grit pad which is the first stage polishing pad again rinsing with water after use. The next two pads are a Fine 1500 grit and Extra Fine 3,00 grit which really build up a high-quality polish on the stone.

Sealing a Marble Tiled Floor

The floor was left to dry off fully overnight and I returned the next day to seal the Marble first checking with a damp meter that the stone was dry. To seal the Marble tiles I applied two coasts of Tile Doctor Colour Grow which is an impregnating sealer that works by occupying the pores in the stone thus preventing dirt from becoming ingrained. Colour Grow also has the added advantage of enchasing the natural colours in the stone and in this case brought out the deep brown colours in the Marble.
Once the sealer had dried the floor was treated to a gentle buff with a white pad to bring up the shine even further.

Marble Tiled Floor After Cleaned and Polished Willington Cheshire Marble Tiled Floor After Cleaned and Polished Willington Cheshire

 
 

Professional Marble Tiled Floor Polishing in Willington



Source link

Restoring Neglected Victorian Hallway Tiles in Norwich


There are thousands of Victorian tiled hallways in and around Norwich and I often get called to work on them, however this was a particularly abused and neglected example I thought you might find interesting. The surface had clearly been both painted red at some point (possibly with an old lead-based paint) and then completely covered with rubber-backed underlay and carpeted, a thick layer of double-sided carpet tape remaining firmly stuck in patches around all the edges of the floor area.

Victorian Hallway Floor Tiles Before Cleaning Norwich

Cleaning a Victorian tiled floor

Firstly, we cleaned the whole area using a strong solution (1:3) of Tile Doctor Pro-Clean, which is a high alkaline stripper and cleaner, agitated with a black scrubbing pad fitted to a rotary machine. All products and slurry were then power rinsed and vacuumed away to reveal the improved floor.

There were still a significant number of glue patches and paint spots around the edges of the floor, so these were tackled using Tile Doctor Remove & Go, which softened them enough to enable us to remove them with a sharp-bladed scraper.

Unfortunately, the decaying rubber underlay had left a pattern on the tile surface which was most obvious at the doorway into the terracotta tiled kitchen. We almost completely removed this using Tile Doctor Oxy-Gel which being in gel form allows it work on the problem area longer. It was painted on a brush and kept moist for two hours under a layer of cling film which drew out virtually all the contaminant from the tile.

The next concern was that an original Victorian floor of this age would almost certainly have no damp proof membrane and an area near the front door which showed evidence of efflorescence salts was treated with Tile Doctor Acid Gel in order to remove the white deposits and further inhibit the production of more in the future.

The whole area was then lightly buffed using the rotary machine and a 1500 grit diamond pad with water in order to remove any remaining fine paint spots and restore a silky feel to the surface of the tiles before leaving the floor to dry overnight with assistance from our dehumidifier.

Sealing a Victorian tiled floor

When we returned the following morning, our damp meter showed us that the moisture content in the substrate was probably going to be too high to allow us to use an acrylic sealer to provide the sheen which the client had requested; so we decided to spray-buff the floor using a 3000 grit diamond pad on the rotary machine followed by the application of Tile Doctor Colour Grow, a colour enhancing penetrating sealer which sits just below the surface of the tile and leaves no visible finish. Finally, the whole floor was spray buffed to a low sheen with a white maintenance pad on the rotary machine and any resulting dust vacuumed away.

Victorian Hallway Floor Tiles After Cleaning Norwich

The Victorian tiles now look fantastic and have become a great asset to the property as original features like these are very sought after.
 
 

Deep Cleaning and Restoration of Old Victorian Tiles in Norfolk



Source link

Restoring an 18th Century Norfolk Pamment Tiled Floor in Wymondham


The client’s requirement for this particular job was to clean and restore a very old and porous Pamment tiled floor in the dining room of an old house in the Norfolk Market town of Wymondham. My client impressed upon me the need to restore the floor without removing any of its considerable character and to provide a high degree of fluid and stain resistance which I was confident would not be an issue having worked on similar floors before.

Pamment Dining Room Floor Tiles Before Cleaning Wymondham

The floor originally dated from the late 18th century and had clearly suffered many years of abuse and neglect; there was evidence that at one time, the entire area had been covered by linoleum which appeared to have been stuck down with a type of hide glue, leaving large patches of the adhesive firmly stuck to the surface of the tiles.

Pamment tiles are very popular in Suffolk and Norfolk homes and I often come across them; they are made from clay and, like Terracotta, are porous and therefore need to be sealed to prevent ingrained dirt. Pamments are quite versatile however and can be used for internal floors and external surfaces like patios.

Cleaning a Pamment tiled floor

The first stage of the renovation was to apply a strong dilution (1:2) of Tile Doctor Pro-Clean to the whole area which was scrubbed in with a rotary machine fitted with a black scrubbing pad. The resulting slurry was power-rinsed and vacuumed away using our Ninja machine which makes light work of these tasks.

Tile Doctor Remove & Go was then applied to the remaining patches of paint and glue and allowed to remain in contact for thirty minutes before being scrubbed again with the black pad and rinsed with clean water. A few particularly stubborn glue patches were finally dispatched by steaming after the application of Tile Doctor Nanotech HBU Remover. The cleaning being complete, the odd bits of missing pointing were replaced using a grey-coloured fast-cure compound and the whole area was left to dry thoroughly overnight with the assistance of our large capacity dehumidifier.

Sealing a Pamment tiled floor

Returning the following day, the floor was tested for moisture content using a damp meter to ensure that the chosen sealer’s performance wouldn’t be adversely affected by the presence of too much water in the substrate, particularly bearing in mind that there certainly wouldn’t be a damp proof membrane present in a floor of this age.

The dehumidifier has done its job and I was able to start the sealing process with a single coat of Tile Doctor Colour Grow which is an impregnating sealer that works by occupying the pores in the tile so dirt cannot. Colour Grow is also a moisture-tolerant, breathable sealer that has the additional benefit of enhancing the colours within this kiln-fired tile without affecting the look and feel of the surface.

Our clients had said that they would prefer a slight shine to the flooring if possible, so a further three coats of Tile Doctor Seal & Go were then applied to the whole area which provided maximum fluid resistance with a mid-sheen finish which would make daily cleaning much easier and more effective.

Pamment Dining Room Floor Tiles After Cleaning Wymondham

The client was really pleased with the transformation and left the following comment.
“Almost unbelievable; the results are far beyond what we hoped might be possible with our badly neglected dining room floor. Many, many thanks.”
 
 

Deep Cleaning and Restoration of Old Pamment Tiles in Norfolk



Source link