Maintaining a Victorian Tiled Entrance in Ilkley


Most stone and tile benefit from the protection that a sealer provides to stop dirt becoming ingrained into its pores. However, the act of walking on the tile causes wear and this over time will lead to the sealer wearing off and dirt reaching the pores; the worse thing is you rarely notice it happening because it takes a long time to wear down a sealer.

Most of my customers have this problem and call on me to clean and reseal the floors every few years when it becomes difficult to clean effectively. The alternative which I do for a number of my clients is to have the floor lightly cleaned and a new layer of sealer added every six to twelve months.

This Victorian tiled entrance at a period house in Ilkley was not in too bad a shape just a little dirty and dull and the owner was keen to have is renovated in the run up to the Christmas holidays. Ilkley is a lovely town in West Yorkshire which became very fashionable in the Victorian era due to the health benefits of the local water, this led to a lot of Victorian architecture and tiled entrance floors like this one are very typical in the area.

Victorian Tiled Entrance Ilkley Before Cleaning Victorian Tiled Entrance Ilkley Before Cleaning

Cleaning a Victorian Tiled Entranceway

To get the dirt out of the tile and grout I applied a strong dilution of Tile Doctor Pro-Clean to the tiles and left it to soak in for fifteen minutes. Pro-Clean is a very reliable cleaner for all types of tile and grout including natural stone, Limestone, Slate and Travertine, amongst others; additionally, when used in a strong dilution it will strip off old sealers. The solution was then worked into the tile using a black scrubbing pad fitted to a rotary machine and the soil extracted using a wet vacuum.

I gave the floor a light rinse with water to remove any trace of cleaning products and then inspected the floor to ensure it was up to standard. At this point I could see there were flecks of paint on the tile around the edges of the floor from previous decorating work and, so I removed carefully removed these with a scrapper and a hand-held diamond block.

The floor was given a final rinse and the wet vacuum used to extract as much moisture from the floor as possible before leaving it to dry for the evening.

Sealing a Victorian Tiled Entrance with a Matt Finish

I returned the next day to seal the floor first discussing the finish that the customer wanted for the tiles. Typically, I recommend using a satin sealer for Victorian tiles as it adds a nice sheen to the tile however surprisingly the owner wanted a matt finish.

Tile Doctor has a full range of sealers available to cater for all requirements so for this floor I applied three coats of Tile Doctor Colour Grow which leaves a matt finish whilst enriching the colours in the tile.

Victorian Tiled Entrance Ilkley After Cleaning

The tiles are now full of life and with the paint specs removed there is now a crisp black edge between the floor and the skirting which the customer also picked up on.

Victorian Tiled Entrance Ilkley Before Cleaning
 
 

Professional renovation of a Dirty Victorian Tiled Entrance in West Yorkshire



Source link

Polishing and Sealing Travertine Tiles in Blackburn


Close-up photo below of a Travertine tiled floor installed in a house in the former mill town of Blackburn where simply put the polished appearance had worn off and was now looking dull and unappealing.

Travertine Tiled Floor Before Polishing Blackburn

I popped round to the house to take a look and could see that the tiles would need to be burnished to restore the polished appearance. To demonstrate the difference this would make I polished one of the tiles using the Tile Doctor burnishing pad system which consists of the application of four 17 inch diamond encrusted pads applied in sequence from coarse to very fine with a rotary buffer. The customer was amazed at the difference and we agreed a date to come in and complete the whole floor in time for the Christmas holidays.

Stripping and Re-Polishing Travertine

On my return I repeated the burnishing process across the entire floor starting with the 400 Grit Coarse Red No.1 Burnishing Pad which strips off old sealers and dirt from the tile. You use a little water to help lubricate and once complete it’s necessary to rinse the area with water to remove the soil that is generated. The next step is to start building back the polish with the 800 and then 1500 grit pads which are applied in the same manner.

Travertine Tiled Floor During Polishing Blackburn

The floor was then rinsed again with water and I turned my attention to the grout which was scrubbed by hand using Tile Doctor Pro-Clean and a stiff brush. The floor was given another rinse and then inspected to ensure I hadn’t missed anything. Before leaving for the day I used the wet vacuum to extract as much moisture from the floor as possible.

At this point the customer commented that the floor looked amazing and that the floor never looked this good, even after it was first installed.

Sealing Travertine Floor Tiles

On the second days we used the 4th burnishing pad which is a 3000 grit pad to burnish and polish the surface until it came up looking gorgeous and glossy. With this pad you simply spray a little water on the floor during the polishing process, something we call a spray burnish.

The last step was to seal the tiles using a single coat of Tile Doctor Ultra-Seal which was applied and then buffed in with a white pad to remove any excess. Ultra-Seal is a premium, no-sheen, natural-look, penetrating sealer formulated to provide maximum stain protection.

Travertine Tiled Floor After Polishing Blackburn

The customer was really pleased with the difference we had made to the floor and before leaving we advised the customer of the best way to maintain the floor using neutral PH cleaners and to avoid strong cleaning products which can erode the life of the sealer prematurely.
 
 

Honed Travertine Tiled Floor Polished in South Lancashire



Source link

Old Flagstone Tiled Kitchen Floor Refurbished in Haslingden Rossendale


This client had contacted us for help renovating their Flagstone hallway floor as nothing they did was helping to keep them clean. The problem with the tiles was due to the pores of the flagstone being ingrained with dirt and once this happens they are really difficult to clean effectively. This is why we always recommend stones floors are sealed after cleaning.

After a successful survey that included measuring background moisture levels and testing different products for stain removal I was able to work out the best process for cleaning the floor and a day to clean and seal the tiles was scheduled.

Flagstone Hallway Floor Before Cleaning Haslingden

Deep Cleaning Flagstone Hallway Tiles

I’d established during my earlier testing that I would need a very strong cleaning product to get the floor clean and deal with the stubborn staining that was present and with that in mind I applied Tile Doctor NanoTech HBU. HBU stands for Heavy Build-Up and is a problem solving tile cleaner and stain remover that adds nano-sized abrasive particles to the mix. This was left to dwell on the floor for a few hours and additionally was covered with a plastic sheet to prevent it from drying out. I then gave the floor a scrub using a black scrubbing pad fitted to a rotary floor machine and a strong dilution of Tile Doctor Pro-Clean for good measure.

Once happy with the result the soiled cleaning solution was extracted using a wet vacuum and the floor given a thorough rinse with water to remove any trace of cleaning products. Again the wet vacuum was used to remove the fluids and extract as much moisture from the stone as possible. The floor was then left to dry out fully overnight assisted with a floor dryer to help accelerate the process.

Flagstone Hallway Floor After Cleaning Drying Out Haslingden

Sealing a Flagstone Tiled Kitchen Floor

We came back the next day and tested the floor with a damp meter in a few different locations to make sure no dampness remained in the stone. The air mover had done its job and the Flagstones were dry so we proceeded to seal the floor with a couple of coats of Tile Doctor Colour Grow which penetrates into the pores of the stone protecting it from within and enhancing the natural colours of the stone.

Flagstone Hallway Floor After Cleaning and Sealing Haslingden

It’s difficult to appreciate from the photographs but the customer was amazed at how much of a difference our process had made and at how much dirt we were able to remove. The flagstones were probably more then 100 years old and more aggressive machinery and cleaning products were the only things that would shift the old dirt. The fresh sealer will also ensure the floor is much easier to clean in future.
 
 

Old Flagstone Hallway Floor Cleaned and Sealed in Rossendale



Source link

Limestone Kitchen Tiles Cleaned, Polished and Sealed in Ashton


It’s always nice when one of our former customers refers their family and friends to Tile Doctor as it’s a testament to the great work we do. As the Tile Doctor for Northamptonshire, I often carry out tile cleaning and restoration jobs in the Oundle area.

Recently, a customer from the nearby village of Ashton was referred to me by a friend. Her friend has the same type of floor in the same type of barn conversion in the area, and had chosen to use our services both last year and this year for their annual maintenance clean.

This new customer had a polished Limestone kitchen floor that was proving difficult to keep clean. The grout had become extremely dirty and – in the absence of an effective sealer – dirt and general muck had easily penetrated the pores of the Limestone itself. The result was a very dull appearance – not one that any property owner wants to suffer!

Polished Limestone Floor Before Cleaning Ashton Polished Limestone Floor Before Cleaning Ashton

On our initial inspection visit, we always carry out a test clean within a small area of the floor to give the customer an idea of the final results they can expect. Upon my first visit to this property, I carried out the test clean and the customer couldn’t believe the difference made to the appearance of the grout lines. In fact, she had even forgotten their original colour!

Cleaning and Burnishing Polished Limestone Kitchen Tiles


When I next visited the property, it was time to carry out the full restoration. The work was carried out in sections of around 10m2 each, with two Tile Doctor technicians on site using the latest Tile Doctor products and machinery.

The issue of the extremely dirty grout lines was tackled first. We cleaned them with Tile Doctor Pro-Clean, which is a high alkaline tile and grout cleaner. We will use Tile Doctor Pro-Clean on all types of natural stone – it’s just that reliable for cutting through the grime. The product was applied using specialised grout brushes and the resulting chemical slurry was rinsed away using fresh water and extracted with a wet vacuum.

Polished Limestone Floor During Cleaning Ashton

Satisfied with the cleanliness of the grout lines, we moved onto improving the appearance of the polished Limestone tiles. When it comes to restoring polished stone, including Limestone, Travertine and Marble, we typically use a process we have developed known as ‘burnishing’. Burnishing involves both cleaning the tile and gradually polishing it to achieve a high-quality, long-lasting sheen finish.

We use a set of four diamond-encrusted burnishing pads fitted to a rotary machine to do this. The first to be applied is a pad with a Coarse grit, which breaks down any old sealer and shaves off the very top layer of the dirty stone, leaving a fresh surface beneath.

Next, burnishing pads with Medium, Fine and Very Fine grits are applied to slowly but surely polish the stone, achieving a very pleasant and shiny appearance. In most cases, the tiles come out looking better than they did when they were originally installed!

Once burnished, the floor was left overnight.

Sealing Polished Limestone Kitchen Tiles


The following day, we returned to seal the tiles. We did this using two coats of Tile Doctor Ultra-Seal, a sealant which is formulated to protect the floor and grout lines against dirt build-up and staining.

Polished Limestone Floor After Cleaning Ashton

The very happy customer was given a complimentary bottle of Tile Doctor Stone Soap, which is a highly concentrated neutral stone cleaner that helps to maintain the patina on polished stone. This will help her keep the appearance of the floor maintained until her next maintenance clean with Tile Doctor.

Polished Limestone Floor After Cleaning Ashton
 
 

Professional Renovation of a Dirty Limestone Tiled Floor in Northamptonshire



Source link

Victorian Tiled Hallway Hidden Under Carpet Restored in Leatherhead


This customer who owned a lovely period residence in Leatherhead had pulled up an old hallway carpet to discover this gem of Victorian Tiled floor. The tiles were covered in carpet adhesive, paint splashes and what looked like a hundred years of dirt. I suspect the previous owners felt it was easier to cover the hallway in carpet rather than have it cleaned properly or perhaps it was just the trend at the time.

Victorian Tiled Hallway Before Restoration in Leatherhead

Given the obvious amount of work that would be needed to restore it we got a call to pop round and provide an estimate. We do a lot of Victorian floor restorations and across the Tile Doctor network I’m confident in saying there is a Tile Doctor working on a Victorian Tiled floor every day of the week.

Victorian Tiled Hallway Before Restoration in Leatherhead

The owner was happy with the quote and we agreed a date to return and restore the floor.

Cleaning a Heavily Soiled Victorian Tiled Floor

Working in a metre square area at a time, I first applied a solution of Tile Doctor Oxy-Gel and left it to dwell for twenty minutes. Oxy-Gel is a relatively new product that being in Gel form is easy to control and stays in place allowing it to dissolve dirt and in this case loosen the adhesive.

After leaving it to dwell for 20 minutes I attacked it with a very coarse 100 grit diamond pad attached to a buffer machine. This removed a minuscule layer from the surface of the tile and with it the muck. I vacuumed up the excess with a wet vacuum then rubbed down the stubborn areas with a 50 grit hand block. This removed a lot of dirt and drastically lightened the whites and blues. Finally I neutralised the floor with two rinses of clean, warm water again using the wet vacuum to remove as much moisture as possible from the floor.

I repeated this process along the length of the hallway and then inspected the floor retreating any areas containing stubborn marks.

Sealing a Victorian Tiled Floor

The hallway wasn’t that big an area so I had agreed to do the whole floor in one day. As a result I needed to force dry the floor so I could seal the tiles in the same day. I have a number of tools to do this including an industrial air mover and a heat gun which were applied for about an hour before it was dry.

To seal the tiles I applied two coats of Tile Doctor Colour Grow which as its name suggests is a colour enhancing sealer that works by impregnating the pores of the tile protecting it from within and enriching the colours in the process. This gave a lovely contrast in colour whilst providing a matt finish; another advantage of Colour Grow is it’s a fully breathable sealer which won’t trap moisture under the tile which is important for these old floors where no damp proof membrane is installed.

Victorian Tiled Hallway After Restoration in Leatherhead

The Victorian tiled hallway floor now looks amazing.
 
 

Professional Victorian Tiled Hallway Restoration in West Surrey



Source link

Porcelain Shower Cubicle Grout Refreshed and Recoloured in Eastbourne


Anyone who wants to put their house up for sale should consider refurbishment projects that can help increase the value of the property and make it more appealing to potential buyers. This is especially the case in rooms with tiled floors or features, which many buyers find particularly attractive. If you’ve left your tiles – whether they’re in the bathroom, kitchen or elsewhere – in a bit of a state, chances are that it’ll put people off.

Recently, I was contacted by a customer who was in the process of refurbishing their house in Eastbourne prior to putting it up for sale. As part of the refurbishment, the customer wanted the Porcelain bathroom tiles to look ts absolute best for anyone viewing the property. While the bathroom room had been installed not too long ago, the grout was not looking very attractive.

Grout Before Changing Colour in Eastbourne Bathroom

This was due mainly to the fact that the grout was looking dark and stained. I was asked to give the tiles and grout a thorough clean before recolouring the grout to make it lighter and more appealing.

Cleaning and Re-Colouring Porcelain Shower Tiles and Grout

To achieve the best results, the grouting in shower cubicles needs to be cleaned before it can be recoloured. To do this, I used Tile Doctor Duo Clean, a product which acts fast to removes any mould and black spots from the grout. If necessary, it can also be used to clean plastic or enamel baths and showers.

The product was applied and then scrubbed into the grout carefully using a specialised grout brush, and the area was left to dry. Once the cubicle was dry, I applied the Tile Doctor Grout Colourant in small sections, so that I could wipe off any excess from the tile surface before it dried.

Grout During Changing Colour in Eastbourne Bathroom

Tile Doctor Grout Colourants are available in 10 different colours, but in this case the customer opted for a normal white as it contrasts nicely with the grey tiles. The Colourant not only recolours the grout lines; it also seals and rejuvenates them.

Grout After Changing Colour in Eastbourne Bathroom

The shower room was quite large, so the job took most of the day to complete. But it was certainly worth it. The customer was very pleased with the results, and we wish them the best of luck with selling the property.

Grout After Changing Colour in Eastbourne Bathroom
 
 

Professional Renovation of a Porcelain Tiled Bathroom in Eastbourne



Source link

120 Year Old Victorian Hallway Tiles Refreshed in Sandwell


Sandwell forms part of an area in the West Midlands which is popularly referred to as the ‘Black Country’. This area industrialised rapidly during the Victorian period and, with the building of many new factories came the building of many new houses for workers.

A good number of these Victorian properties survive, complete with original Victorian tiled floors. However, homeowners aren’t always aware that these tiled floors exist, since they have often been covered up by carpet or linoleum. We find that when new homeowners discover these original tiles, they are usually keen to restore them to their best possible appearance. This requires professional assistance.

Victorian Tiled Floor Before Renovation Warley

A customer who lives in the Warley district of Sandwell recently contacted me about the restoration of a 120-year old Victorian tiled hallway that they had discovered underneath an existing carpet. As expected, the tiles were caked in deposits of adhesive, cement and paint which had accumulated over several years. Making matters worse, the customer had also spilt more paint on the tiles during decoration work.

Victorian Tiled Floor Before Renovation Warley

Cleaning an Original Victorian Tiled Hallway

I began the restoration by cleaning the tiles with Tile Doctor Pro-Clean, a strong alkaline cleaner which is perfect for removing grime from heavily soiled and neglected natural stone. The product was applied liberally across the area and left to dwell for a short period. It was then worked into the tiles using a specialised rotary cleaning machine fitted with a black scrubbing pad.

The now soiled cleaning solution was subsequently rinsed away and the floor then rinsed with clean water. Stubborn paint marks and cement were carefully scraped off the tiles by hand. A solution which combined more Pro-Clean and Tile Doctor Remove and Go (a stripping agent) was applied to the tiles to help remove any old and now ineffectual sealer, as well to fully remove any of the particularly stubborn marks.

After being worked in again with a scrubbing pad fitted to a rotary machine, the excess cleaning product was rinsed away using water and the floor was dried off with a wet vacuum.

As tiles of this age were usually laid without a damp membrane in place underneath them, they can be especially prone to efflorescence (salt) deposits. To help prevent this, Tile Doctor Acid Gel, which is a combination of phosphoric and hydrochloric acids, was applied. This will help to neutralise any alkaline salts that might threaten to penetrate up through the tiles to leave unsightly white marks.

After the floor was rinsed once again, I proceeded to re-grout a few areas of the floor where the grout had worn away over the years. Once I was happy with the clean tiles and fresh grout, I left the floor to dry off overnight.

Sealing an Original Victorian Tiled Hallway

The next day the tiles had thankfully dried completely and were ready to be sealed. Since the customer had requested a sheen finish, as opposed to be a natural matte finish, I opted to use a combination of two different sealants.

The first to be applied – to bring out the colour in the tiles – was Tile Doctor Colour Grow. This product impregnates the tiles to protect them against ingrained dirt, but it leaves a matte finish. Therefore, I added five coats of Tile Doctor Seal and Go to provide not only extra protection, but also a high-quality sheen finish.

Victorian Tiled Floor After Renovation Warley

I left the customer, who was delighted with the results, with a bottle of Tile Doctor Neutral Tile Cleaner. This product will serve as a reliable cleaning product for the routine maintenance of the tiles, ensuring they continue to look fantastic.

Victorian Tiled Floor After Renovation Warley
 
 

Professional Restoration of an Original Victorian Tiled Hallway in the West Midlands



Source link

1877 Victorian Tiled Church Floor Restored in Rishton


Earlier this year I was asked to restore a number of Victorian tiled floors at the St. Peter & St. Paul’s Parish Church in Rishton near Blackburn. The Church has a lot of carpet flooring and some had to be removed due to some other work that was going on and these tiles were discovered underneath. The Vicar believe the tiles are originals and date back to 1877.

Victorian Floor Before Cleaning Rishton Church

You can see from the photograph above that the tiles were discoloured with years upon years of ingrained dirt but what you can’t see is the adhesive that was used to secure the carpet to the tile. The whole floor and the Altar behind would need several deep cleans to remove the dirt and glue and being a busy church with an active congregation it would need to be done in a few days. In need of an extra pair of hands I gave Derbyshire Tile Doctor Henri Mall a call and he was more than happy to help me out.

Victorian Floor Before Cleaning Rishton Church Victorian Floor Before Cleaning Rishton Church

Deep Cleaning Old Victorian Church Tiles

To begin, I took moisture readings over all areas due to be worked on; Damp Proof Membranes were not invented until relatively recently, so it pays to know in advance how damp the floor is. Next, I gave the floor a quick clean in Tile Doctor Pro-Clean, mainly to remove any surface dirt and grit. This was then followed by the application of a 200 grit burnishing pad to grind off surface dirt and excess glue so we access the pores of the tile. The resultant soil was then rinsed off with water and then extracted using a wet vacuum.

The next step was to give the tiles a good soak in a solution of NanoTech HBU remover (HBU stands for Heavy Build-Up) which was then scrubbed in using a black pad fitted to a rotary floor machine. This process worked well to release the ingrained dirt from the tile and took off a lot of the glue however it took quite a few iterations and the use of a portable steamer to really get the floor clean.

Victorian Floor During Cleaning Rishton Church Victorian Floor During Cleaning Rishton Church

There was a lot of tile to do so working in sections it took Henri and I two days to really get the floor clean. A lot of water was used in the process and although a lot of the moisture was extracted using a wet vacuum we felt it best to leave the floor to thoroughly dry out for a couple of days.

Sealing Old Victorian Church Tiles

The floor needed to be dry before sealing so on our return I checked the floor with the damp meter and compared it with my previous readings. All was so Henri and I started applying the first coat of Tile Doctor Colour Grow, an impregnating and breathable sealer ideal for this situation. Colour Grow seeps into the pores of the tile protecting it from within and enhancing the colours in the tile. Three coats were needed so it took most of the day to complete.

Victorian Floor After Cleaning Rishton Church Victorian Floor After Cleaning Rishton Church

While it was a lot of work we were very both pleased with the outcome, as was the Vicar who left the following comment on the Tile Doctor feedback system.

Many thanks to Tony Olmet, not only a very good job but he worked tirelessly, never stopped, to get it done. Nothing a problem, very helpful chap. Recommended.
Christopher Holden (vicar), Rishton 14 July 2017

Victorian Floor After Cleaning Rishton Church
 
 

140 Year Old Victorian Tiled Church Floors Restored in the Diocese of Blackburn



Source link

Dirty Paint-Marked Victorian Tiled Entranceway Restored in Roundhay


Roundhay is an affluent area of North Leeds which is well-known for the fantastic Roundhay Park. The park is large enough to contain two lakes, extensive woodland, formal gardens and even golf courses! It’s the premier attraction for anyone fortunate enough to live in the area, or anyone visiting from nearby.

I recently visited a customer who lives in Roundhay and was looking for help in restoring the small Victorian tiled entranceway at the front of her house. The tiles were in a shocking state, but it’s not hard to imagine why – the entrance to a house receives a lot of foot traffic and is not typically taken care of regularly. These tiles were also marked with paint splashes left over from decoration work, making them look even worse.

Small Victorian Entrance Before Cleaning Roundhay

The appearance of the entranceway did not set the right standard for the rest of the house, so the property owner was keen to have it restored professionally.

Cleaning a Victorian Tiled Entranceway

I informed the customer that I could have the tiles rejuvenated within a day’s work. To begin, I used a scrapper and wire wool brush to manually remove some of the most stubborn paint marks.

Following this, I applied a strong solution of Tile Doctor Remove and Go, before leaving the product to dwell for about an hour. Remove and Go is multi-purpose stripping agent that can remove any adhesive and paint deposits, as well as many types of old coatings and sealers.

To work the product deep into the tiles, I agitated with an abrasive cleaning pad and then rinsed the area with fresh water. This had the desired affect and all the unsightly paint marks were removed.

Next, I gave the floor another thorough clean to remove any general muck and ingrained dirt. This was done using our high-alkaline cleaner, which we typically use on Victorian tiles, known as Tile Doctor Pro-Clean. In fact, Pro-Clean is a very reliable cleaner for all types of tile and grout including natural stone, Limestone, Slate and Travertine, amongst others.

Sealing a Victorian Tiled Entranceway

Since I told the customer I would able to finish the job within a day, I dried the floor quickly using a heat gun so it could be sealed there and then. To seal the floor, I applied four coats of Tile Doctor Seal and Go, which is a topical sealer formulated to provide maximum protection along with a high-quality, low sheen finish.

Small Victorian Entrance After Cleaning Roundhay

As you can see from the photos above, the entranceway was absolutely transformed. These tiles are now a true asset to the rest of the property, rather than looking out of place! I’m please to say my customer was amazed by how quickly such a big difference could be made and left the following glowing feedback.

I can’t believe the before and after pictures. The restoration of the tiles is top quality, they are so much brighter and richer in colour – especially without the garage paint hiding the detail! Nigel did an amazing job, even better than I could have hoped for, and is a lovely guy as well. Would definitely recommend.
 
 

Professional Tile Cleaning and Sealing for a Dirty Victorian Tiled Entranceway Restoration in North Yorkshire



Source link

Renovating Travertine Kitchen Floor Tiles in Sanderstead


This customer, who lives in Sanderstead located between Croydon and Purley in Surrey had been experiencing difficulties in keeping her beautiful Travertine tiled kitchen floor in good condition. Over the years it had suffered from a heavy build up of dirt and oily stains, not to mentioned a number of cracks and small holes. Needless to say, the customer was keen to have the Travertine tiles and grout renovated and made easier to keep clean.

Travertine Kitchen Floor Before Cleaning Sanderstead Travertine Kitchen Floor Before Cleaning Sanderstead

Restoring Travertine Flooring

To begin the renovation, I applied Tile Doctor Remove and Go across the entirety of the large tiled area. This heavy duty remover breaks down any old sealers and other coatings, leaving the area ready to cleaned or, in this case, burnished.

Burnishing is a method for cleaning and polishing certain types of high-end stone, including Travertine, Marble, and Limestone. Our burnishing system involves the application of four diamond encrusted pads of varying grits. Firstly, I applied the Coarse grit pad, which helps to break down any dirt and stains on the surface of the tiles. Then, I worked my way through the Medium, Fine, and Very Fine pads, using a little water which acts to lubricate the process gradually building the polish on the Travertine. The floor is rinsed with water between the application of each pad to remove the soil that is generated and also give a final rinse at the end before leaving to dry.

To round off the first day of work, I filled any cracks and holes in the Travertine using a colour matching resin which greatly improved the look of the tile.

Travertine Kitchen Floor Cracked Tile Before Repair Sanderstead Travertine Kitchen Floor Cracked Tile After Repair Sanderstead

Sealing Travertine Tiles

The following day I returned to the property to seal the tiles checking first that the floor had dried. I use a moisture meter to do this and it confirmed the floor was dry so I proceeded to seal the floor using our colour intensifying impregnating sealer Tile Doctor Colour Grow. Once that was dry, I added the finishing touches by buffing the floor with a soft white buffing pad. As you can see from the photographs, the combination of a fresh seal and polish worked wonders.

Travertine Kitchen Floor After Sealing Sanderstead

We did such a good job with the floor that the customer asked if we could also improve the appearance of their natural stone fireplace which was suffering from bad rust and oil stains however I do a separate write up on that.

Travertine Kitchen Floor After Sealing Sanderstead
 
 

Cracked Travertine Tiled Kitchen Floor Fully Restored in Surrey



Source link

Slate Tiled Floor Rejuvenated at New Barn Conversion in Farnham


Converting a barn into a property can be an exciting project, but it certainly doesn’t come without a range of challenges. If done correctly, they can look amazing and are well worth the effort.

A recent customer of mine had spent the last six months converting a barn into a residential property in the West Surrey town of Farnham. While the project had been a big success, the house had been subjected to high traffic from dozens of carpenters, electricians and builders. This had taken its toll on the newly installed Slate tiled floor – so the property owner asked me to restore it to its peak condition to complete the conversion once and for all.

Slate Tiled Floor Before Cleaning Farnham

Before accepting the job, I strongly advised the customer that I should be the last workman out of the door. In my experience few tradesmen are known to take care of other peoples work and any further work being done in the property could potentially spoil the appearance of the Slate tiles.

Slate Tiled Floor Before Cleaning Farnham

Cleaning a Slate Tiled Floor

The customer was happy for me to proceed, so on the agreed date I returned and started the work by laying down a strong dilution of Tile Doctor Pro-Clean across the floor. Pro-Clean is an alkaline-based cleaner which breaks down all manner of dirt and grime.

This was a large area of tiles, so I worked on individual sections of 3m2, first soaking the Slate in Pro-Clean and then waiting ten minutes for it to soak in and then following with a nylon black scrubbing pad fitted to a 17-inch rotary buffing machine to work the cleaning product into the stone. The tiles immediately came up looking much cleaner. Any excess water and chemical slurry was vacuumed up promptly with a wet vacuum.

The tiler had done a good job of laying the floor and removing any excess grout as normally my next step at this point would be to give the floor an acid wash, but it wasn’t necessary.

Once the tiles had been cleaned to the best of my abilities and given a thorough rinse, I left the property for 48 hours to allow any water that had seeped into the tiles to evaporate. This is important as excess moisture problems can prevent the tiles from being sealed correctly.

Sealing a Slate Tiled Floor

On returning to the property a couple of days later, I swept away any bits of dust and debris and then proceeded to seal the tiles with Tile Doctor Colour Grow.

Slate Tiled Floor After Cleaning Farnham

This impregnating, colour-intensifying sealer enhanced the stunning natural brown, gold and orange shades in the stone. Two coats of the sealer were applied to achieve a brilliant natural-look finish and robust protection against future wear and tear.
Restoring the appearance of these Slate tiles put the finishing touches on this fantastic barn conversion. Needless to say, the customer was very pleased with the results.

Slate Tiled Floor After Cleaning Farnham
 
 

Recently Laid Slate Tiled Floor Given Builders Clean to Restore Appearance in Surrey



Source link

Very Dirty Quarry Tiled Kitchen Floor Restored in Rotherfield


Looking at the pictures below you might think this Quarry Tiled kitchen floor at a cottage in Rotherfield was as old as the village which dates back to the 8th Century and is mentioned in the Doomsday book. It really was in a bad state with I don’t know what covering the tiles which had gone black as a result but were actually very pretty as you will see later.

The client was having a new kitchen fitted and wanted the tile and grout restored so as not to incur the cost of replacing it. This really is the best time to look at getting your tiles thoroughly cleaned as with many of the old units removed I could access most of the floor and of course I didn’t need to worry about protecting the units either.

Dirty Quarry Tiled Kitchen Floor Before Cleaning Rotherfield

Cleaning Dirty Kitchen Quarry Tiles

I could see this floor was going to be a challenge so decided to try a strong cocktail of Tile Doctor Pro-Clean and Nanotech HBU, HBU stands for Heavy Build-Up so quite appropriate I thought. Working in sections the floor was soaked in the cleaning cocktail and left to dwell for some time in order to soften the dirt and grime.

Dirty Quarry Tiled Kitchen Floor During Cleaning Rotherfield

The next step was to run over the tiles with a set of Burnishing pads which are encrusted with industrial diamonds. It took more than one attempt at this process but the abrasive pads had the desired effect and eventually revealed the beautiful quarry flooring below.

Dirty Quarry Tiled Kitchen Floor During Cleaning Rotherfield

The pads are effective on the tiles but the grout sits a little lower and so to reach these a stiff brush was scrubbed into the grout by hand.

To remove the dirt that was released from the cleaning process and further clean the tiles I used a Spinning Tool through the process. The tool is powered from a large compressor that sits in my van which forces hot water under pressure onto the tiled floor whilst simultaneously extracting the dirty water back to a tank on the van. It’s an amazing tool that is very effective however you do need to have the van parked very close the house due to a limitation on the hose lengths.

Dirty Quarry Tiled Kitchen Floor During Cleaning Rotherfield

With the tiles now clean and rinsed with water the floor was dried as much as possible with a wet vacuum.

Sealing Kitchen Quarry Tiles

The floor was left to dry for a couple of days before I returned to complete the restoration with the application of a sealer. I tested the floor with a damp meter on my return to ensure it was dry; all was well so I moved onto sealing. Sealer of choice on this occasion was Tile Doctor Seal and Go which is a water-based sealer which so it doesn’t leave a smell as it dries. The Quarry tiles were quite porous, which is not uncommon for Quarry Tiles and six coats of sealer were required in the end.

Dirty Quarry Tiled Kitchen Floor After Cleaning Rotherfield

As the photographs show, the floor was transformed and my customer was elated with the results saying “wow it’s like new!”

Dirty Quarry Tiled Kitchen Floor After Cleaning Rotherfield
 
 

Professional Restoration of a Dirty Quarry Tiled Floor in East Sussex



Source link

Cream Limestone Kitchen Tiles Burnished and Sealed in Ilkley


Ilkley is a wonderful little spa town in North West Yorkshire and a popular destination for tourists visiting the Yorkshire Dales. It’s particularly notable for its quaint tearooms, beautiful countryside and challenging rock climbing opportunities. The town itself is well populated, with approximately 15,000 residents.

Recently, I visited one of the homeowners in the town who was in the process of selling the house. To help make the house more attractive to potential buyers they wanted to make sure the Cream Limestone tiles laid throughout the Kitchen and Dining room were in the best possible condition. The floor was comprised of four different sizes of Limestone tile, laid geometrically.

The floor had originally possessed a natural matte finish, but a satin sealer had been applied at some point in the past to enhance its appearance. Over the years, this sealer had worn away and the Limestone had become dull and dirty, especially in the high foot traffic areas. The grout was similarly in a bad way.

Cream Limestone Floor Tiles Before Cleaning Ilkley Cream Limestone Floor Tiles Before Cleaning Ilkley

I spoke with the property owner about the options for cleaning the floor, outlining the merits of a restoration using our Tile Doctor burnishing pad system, a process which involves polishing the tiles with special diamond encrusted pads of various grit levels. The result would be a high-quality finish which could subsequently be preserved using a sealant.

I felt it was the best course of action to restore the appearance of the Limestone tiles. Even though the customers didn’t want to spend a lot (understandable as they were moving out), they agreed to proceed.

Cleaning a Cream Limestone Tiled Kitchen Floor

I started the restoration by cleaning the grout lines with Tile Doctor Pro Clean, which is a suitable alkaline-based cleaner for natural stone tiles and grout. The product was scrubbed into the grout lines with a stiff brush. Once I was happy that the grout had been completely cleaned of any soil, I rinsed the cleaning solution away and extracted the slurry using a wet vacuum.

The next step as to apply each of the four diamond encrusted burnishing pads in the Tile Doctor system. In this process, we start with the Coarse grit pad to grind away the very top layer of the dirty stone. We then move through the system to apply Medium, Fine and finally the Very Fine pad to gradually refine the polish on the floor. Each pad is used with a small amount of water for lubrication.

Sealing a Cream Limestone Tiled Kitchen Floor

Since this was a large area to restore, it took around two days before the grout cleaning and tile burnishing work was completed.

Some fabulous results were achieved by the burnishing work, and I came back on the third day to seal the tiles with Tile Doctor Ultra-Seal. Ultra-Seal is a natural-look impregnating sealer that will protect the floor for some time to come.

Cream Limestone Floor Tiles After Cleaning Ilkley Cream Limestone Floor Tiles After Cleaning Ilkley

The customers were so pleased with the outcome that they even joked that they no longer wanted to move! I’m glad that they are happy with the results and I’m sure the new property owners will be too.
 
 

Professional Renovation of a Cream Limestone Tiled Kitchen Floor in Yorkshire



Source link

Travertine Kitchen Tiles Deep Cleaned and Sealed in Lincoln


Travertine is a lovely beige and brown stone that looks fantastic when it’s first laid but needs work to maintain the appearance. This was exactly the problem my customer who lives near the historic Cathedral City of Lincoln had experienced. The sealer on their Travertine Kitchen floor was becoming worn in the more commonly used parts of the floor letting dirt become ingrained into the pores of the stone and the grout was also becoming darker where it was getting dirty. They also had pets that spent a lot of time in the Kitchen which didn’t help and there were also small holes in the Travertine that were trapping dirt and would need filling.

Travertine Kitchen Floor Before Cleaning Lincoln

Cleaning and Burnishing a Travertine Tiled Floor

To deep clean the stone and grout I applied a strong dilution of Tile Doctor Pro-Clean, left it to soak in for ten minutes and then worked it into the floor using a scrubbing pad fitted to a rotary floor machine. Pro-Clean is a strong reliable alkaline product which is safe to use on stone and grout including Travertine and Limestone.

Travertine Kitchen Floor Before Cleaning Lincoln

I also ran a stiff grout brush along the edges of the floor and especially along the grout lines to get the grout as clean as possible; the scrubbing pad struggles to reach into the recesses of the grout so it’s best to do this by hand. The now dirty cleaning solution was extracted from the floor using a wet vacuum and rinsed with water to ensure the tile and grout was now clean and any stubborn stains spot treated.

Travertine Kitchen Floor During Cleaning Lincoln

After the deep clean we filled the holes as required using flexible filler which gives a really smooth look to the flooring. We then left our turbo dryer system on overnight to thoroughly dry out the floor before returning to seal the tiles on day two.

Sealing a Travertine Tiled Floor

The next day I returned to the property and proceeded to seal the Travertine tiles using two coats of Tile Doctor Colour Grow sealer to protect the tiles and also really enhance the natural colours in the stone. As an impregnating sealer, Colour Grow penetrates into the stone and fills its pores to safeguard it against ingrained dirt and stains from within.

Travertine Kitchen Floor After Cleaning Lincoln

As you can see from the photographs, the combination of a deep clean, high quality polish and fresh seal really transformed the appearance of the floor from dull and lifeless to a really asset to the kitchen. The customer was so happy with the results she has booked us in to carry out the same work to other flooring in the property.

Travertine Kitchen Floor After Cleaning and Sealing Lincoln
 
 

Professional Maintenance of a Travertine Tiled Kitchen Floor in Lincoln



Source link

Deep Cleaning, Sealing and Polishing 120m2 Limestone Tiled floor in Biddenham


The client from the Bedford village of Biddenham had requested a quote to restore the look of their Limestone floor tiles which were laid throughout the whole ground floor including lounge, hallway and kitchen covering approximately 120m2 in total. The floor needed a thorough clean, filling of holes in high traffic areas followed by polishing and then sealing.

Limestone Tiled Lounge Floor Before Cleaning Biddenham

Over time, the floor in this busy household with 2 large dogs had become dirty and certainly worse for wear with all the use it had been getting. A quote was given and accepted and work was booked in to be carried out over 4 days with 2 Tile Doctor technicians on site for 2 of those days.

Limestone Tiled Kitchen Floor Before Cleaning Biddenham

Deep Cleaning Limestone Floor Tiles

We returned on the agreed date and started work to get this floor back to looking its best. My initial task before beginning the cleaning process was to apply a protective wrap around the oak doors and moving heavy furniture with sliders that the client couldn’t move themselves to give us a clear area to work in.

Limestone Tiled Hallway Floor Before Cleaning Biddenham

We then applied Tile Doctor Pro-Clean, diluted with water, to the floor. Pro-Clean is a strong alkaline cleaner that is suitable for use on all natural stone floors such as Limestone, Slate and Travertine.

After leaving the solution to dwell for a few minutes, We began to scrub over sections (Approximately 10m2 at a time) with a 17” scrubbing pad fitted to a buffing machine, whilst helping to remove a lot of the built up dirt on the surface of the tiles, the products also stripped off the old sealer, this was then rinsed and removed using a wet pick up machine. Following this we paid special attention to the grout lines, scrubbing with grout brushes and Tile Doctor Grout Clean-Up.

After completing the cleaning, I rinsed the floor again with clean water to remove any excess cleaning products. I then began to burnish the floor using Tile Doctor Diamond encrusted burnishing pads. This was done in four steps, as I used four different pads (coarse, medium, fine and very fine) rinsing the floor with water between each pad. Starting with a coarse pad and then gradually working up to the very fine pad achieving a high polish finish in the process. I finished off the process with a quick rinse and a white buffing pad to give the floor a final polish before I commenced the sealing of each area the following day to allow grout and stone to fully dry overnight.

Sealing Limestone Floor Tiles

The client requested a natural look finish so my choice of sealer was Tile Doctor Ultra Seal which will protect the floor but not change the colouring in any way. The sealer penetrates deep into the pores of the stone, providing water resistance and long-term protection from ingrained dirt and stains.

Limestone Tiled Kitchen Floor After Cleaning Biddenham Limestone Tiled Lounge Floor After Cleaning Biddenham

This was a large area so it took some time to complete but it was well worth the effort, certainly the customer thought so and left the following feedback on the Tile Doctor Feedback System.

Phil and his team were polite, friendly and professional at all times. Nothing was too much trouble for them and they worked very diligently to ensure they got the best possible outcome and the floors l. . . ok better than new at the end.

As you can see from the comments the client was extremely happy with the results and he has asked for details of our maintenance plan to keep his floors looking their best for years to come.

Limestone Tiled Hallway Floor After Cleaning Biddenham
 
 

Large Limestone Floor Renovation in Bedfordshire



Source link

Dirty Victorian Tiled Hallway Deep Cleaned and Sealed in York


As promised below are the photographs from the second floor I cleaned recently at a house in historic city of York. If you recall the first floor was Mexican Terracotta which proved pretty tough to clean as the rotary floor scrubber I use struggled to cope with the bull nose edges. You can find the article I created for that floor via the link below:

Mexican Terracotta Tiles Deep Cleaned in York.

The second floor was a Victorian tiled hallway which like its neighbour was dull, lifeless and now overdue a deep clean to remove ingrained dirt, part worn sealer and then reseal.

Victorian Tiled Hallway Floor Before Cleaning York

Cleaning Victorian Tiles Tiles

As with the Terracotta tiles I cleaned the floor using a strong 1:3 dilution of Tile Doctor Pro-Clean with water. This is a strong dilution ratio which will not only clean the tile but also strip off what was left of the original sealer. You need to do this as the sealer will wear off first in the most commonly used part of the floor first which in this case is down the middle of the hallway. I left the solution it to soak into the tile for about ten minutes before scrubbing it in with a black scrubbing pad fitted to a rotary floor machine. I the scrubbed along the grout lines with more pro-clean and a stiff narrow brush by hand to ensure the grout was also clean.

The floor was rinsed with water and the soiled cleaning solution was extracted using a wet vacuum. I could then see those area’s that needed more work and re-treated them with more Pro-Clean until I was satisfied all the previous sealer was gone and the tile and grout was as clean as it could be.

The tiles were given a final rinse with water and the wet vacuum used again to extract as much moisture off the floor as possible. The next step would be to seal, however the Terracotta floor tiles needed a longer drying time so I left both floors to dry out for two days before returning.

Sealing Victorian Tiles Tiles

Upon my return to the property I ran some quick damp tests, which revealed the tiles were ready to be sealed. I then applied four coats of Tile Doctor Seal and Go which provided a beautiful satin finish that really improved the look of Victorian Tile.

Victorian Tiled Hallway Floor After Cleaning York

The hallway tiles now looked clean and much brigher, needless to say my customer was very happy with the transformation.
 
 

Victorian Tiled Hallway Deep Cleaned and Resealed in Yorkshire



Source link

Dirty Mexican Terracotta Tile and Grout Deep Cleaned and Sealed in York


A few months back I posted a story about cleaning Catalan Terracotta tiles where I mentioned that Terracotta tiles are made all over the world. To prove the point I thought you might be interested to read about this Mexican Terracotta Tiled floor I cleaned recently at a house in York.

The customer actually had two floors they wanted me to clean, the other was a Victorian Tiled floor which is cleaned using a similar process but I’ll post about that separately. Both floors looked a bit tired but especially the Mexican Terracotta which looked dull and lifeless additionally the Grout had gone black when it should have been a Sandstone colour.

Mexican Terracotta Floor Before Cleaning York Mexican Terracotta Floor Before Cleaning York

Mexican Terracotta tiles are invariably hand made and made to the same standard as other makes such as Spanish, as a result the porosity levels between each tile can vary greatly which makes them harder to maintain.

Cleaning Mexican Terracotta Tiles

I cleaned the floor using a strong 1:3 dilution of Tile Doctor Pro-Clean with water which is an effective alkaline Tile and Grout cleaner that will clean and strip old sealers from tiles when used in a strong dilution such as on this occasion. I left it to soak into the tile for about ten minutes before scrubbing it in with a black scrubbing pad fitted to a rotary floor machine. This process made a different but the machine couldn’t cope with the “Bull Nose” edges to I had so spend a lot of time cleaning the old fashioned way using a scrubbing brush and a lot of elbow grease. I had the same issue with the grout which being slightly recessed wasn’t cleaned sufficiently by the machine; however I have narrow scrubbing brush that works well for this purpose.

Mexican Terracotta Floor During Cleaning York

The floor was rinsed with water and the soiled cleaning solution was extracted using a wet vacuum. I could then see those area’s that needed more work and spot cleaned them with more Pro-Clean until I was satisfied all the previous sealer was gone and the tile and grout was as clean as it could be.

The tiles were given a final rinse with water and the wet vacuum used again to extract as much moisture off the floor as possible. The next step would be to seal, however the tiles would need to be dry for that to happen and given Terracotta is notoriously porous and absorbs water quickly l decided after I’d leave the floor to dry out for two days.

Sealing Mexican Terracotta Tiles

Upon my return to the property I ran some quick damp tests, which revealed the tiles were ready to be sealed. I then applied four coats of Tile Doctor Seal and Go which provides a satin finish and really improves the look of Terracotta.

Mexican Terracotta Floor After Cleaning York Mexican Terracotta Floor After Cleaning York

My customer was very happy with the transformation that had occurred to their floor and I think you will agree from the photographs the floor looks much healthier.
 
 

Mexican Terracotta Tile and Grout Renovated in Yorkshire



Source link

Quarry Tiled Floor Restored at Historic Cottage in Dunsfold


Dunsfold is a very small village in the borough of Waverley in West Surrey. It’s well known for the Dunsfold Aerodrome, an airfield that was built by the Canadian army during World War II. Hundreds of years ago, members of the English aristocracy held large estates of land in and around Dunsfold – and several historic cottages still exist in the area.

A customer of mine had recently bought one of these cottages and, during renovation work, had removed the downstairs carpets in three rooms to discover a Quarry tiled floor. Naturally, they were caked in many years’ worth of muck and carpet glue.

It would be a significant job to get the tiles in the three rooms back to looking their best – but it was a job I was more than willing to undertake. Classic Quarry tiles exude a certain rustic quality and charm – a welcome addition to many vintage properties, especially those located out in the countryside.

Quarry Tiled Floor Before Renovation at Dunsfold Cottage Quarry Tiled Floor Before Renovation at Dunsfold Cottage

Deep Cleaning a Quarry Tiled Floor

I started the restoration by soaking small areas of the floor in Tile Doctor Remove and Go. This product is excellent for removing floor coatings such as old sealers as well as shifting stubborn filth and loosening carpet adhesive deposits. After carefully scraping any excess adhesive off manually with a sharp blade, I ran my buffing machine across the floor and immediately the tiles cleaned up well.

Next, I used a 200-grit (Coarse) diamond-encrusted burnishing pad on the floor. This basically skims a layer off the tile surface, revealing the original colour of the stone that had previously been hidden underneath. A small amount of water was used as lubrication for this process. Quarry tiles are naturally very porous so after rinsing the soil off the floor I left them over the weekend to dry.

While the somewhat aggressive approach of burnishing is highly effective, it can leave the tiles looking a little washed out – and the colour slightly diminished. However, I assured the customer that the colour would return once the tiles had been sealed.

Sealing an Original Quarry Tiled Floor

While I was enjoying my weekend off, the customer fortunately found a few replacement Quarry tiles in his attic to fit around the fireplace as upstands where there were some tiles missing. So, on my return to the property my first task was to fit these replacements, before sweeping the floor clear of any debris.

To finish the restoration, I applied a couple of coats of Tile Doctor Colour Grow, an impregnating sealant which provides the matte, natural-look finish the customer wanted. This sealant penetrates into the pores of the tile, so it dries inside the stone not on the surface. It also intensifies the fantastic red shades in the Quarry.

Quarry Tiled Floor After Renovation at Dunsfold Cottage

Around an hour after the coats of Colour Grow had been applied, the floor was dry and free to be walked on, and all the furniture could be returned. Much needed life and character had been restored to the Quarry tiled floor and the new property owner was very happy as a result.
 
 

Professional Restoration of a Quarry Tiled Floor Restoration in Surrey



Source link

Restorative Cleaning of a Stone Fireplace in Brighton


I’m really pleased with the transformation I managed to achieve cleaning this Stone Fireplace at a lovely period house in Brighton. The client had been decorating the room which highlighted just how grubby the Stone Fireplace now looked and she desperately wanted to use it for the cold nights towards Christmas.

Stone Fireplace Before Cleaning Brighton

The run up to Christmas is generally a busy time for us as we usually find homeowners are really keen to have their tiles cleaned in time for the festivities. However these jobs tend to only take a day at most so I was confident I could squeeze it in quite quickly.

Stone Fireplace Before Cleaning Brighton Stone Fireplace Before Cleaning Brighton

Cleaning a Stone Fireplace

Before starting any job I make sure the surrounding furnishings are protected from splashes from the cleaning products we use. I tend to use a thin blue film for this as it sticks well to most surfaces and like professional decorators masking tape it doesn’t remove the paint when you remove it later.

Stone Fireplace During Cleaning Brighton

To clean the fireplace I used a diluted combination of Tile Doctor Pro-Clean and Acid Gel which was applied to the stone and left to soak in for few minutes before scrubbing it by hand and then carefully rinsing it off. Pro-Clean is a powerful cleaning product on it’s own but I needed something that would deal with the soot and Acid Gel is able to remove all sorts of deposits plus being a gel it sticks well to vertical surfaces.

I couldn’t really use any machinery on the Fireplace that would make the job easier so I had to use a lot of elbow grease instead. The intricate carvings in the stone took some time to get really clean and so in total the job took me about four hours. The Stone Fireplace was transformed by the time I had finished and I think you will agree it now looks fantastic.

Stone Fireplace After Cleaning Brighton

Brighton is a great place to go shopping especially around “The Lanes” behind the main promenade where they have lots of unusual gift shops and with Christmas looming I was able to spend what was left of the afternoon roaming around.
 
 

Large Stone Fireplace Cleaned and Sealed in East Sussex



Source link